|
|
#1
02-12-2007, 02:56 PM
|
||||
|
||||
What happened?
Well, I got my VerC T-board today for my 06 Electra. Finally got it installed and put back together so I thought I would run some T-Balls through it. Everything went fine for the first 100 balls or so then all of a sudden air started hissing out from the frame...felt like it was coming right out of the grip. The bolt had completely recocked before the air started coming out. I am thinking maybe I have to change the cup seal?? I don't know what else could have happened....can someone help me out? Thanks for your help!!
__________________
Custom red anno Proto PM6 w/ UL frame, Lucky board w/ red eyes, CCM feedneck w/ Sundragon lever-lock Dust black Dye DM7 w/ Virtue board, blue laser eyes, CP flow plug, CP rake trigger 
|
|
#2
02-12-2007, 02:59 PM
|
||||
|
||||
Re: What happened?
I would guess your cupseal either got unscrewed or is no good anymore. Try replacing it and try again.
__________________
Romans 6:23 “God never promises to remove us from our struggles. He does promise, however, to change the way we look at them.”-Max Lucado The most he did was die for me, the least I can do is live for him.
|
|
#3
02-12-2007, 03:01 PM
|
||||
|
||||
|
Re: What happened?
sounds like your on the right track with the cupseal. Have you tried putting a couple of drops of marker oil in the ASA and then dry firing the marker with the barrel removed (you don't want to get the marker oil in your barrel)? Might work, and save you pulling apart your marker just to find out that the cupseals OK.
__________________
Never go Bear hunting without a sandwich...sandwich: someone you can out run or don't mind shooting  Angel 1 Non-SOM Apr 07 Ripper 3 Non-SOM Apr 08 Family Photo My Feedback
|
|
#4
02-12-2007, 03:05 PM
|
||||
|
||||
Re: What happened?
It's nice to have the access to this forum...Within five minutes, two responses! Thanks for your help guys! I am gonna try putting some oil in the ASA quick and hopefully that will work! Any other suggestions, let me know! Thanks again for your help!!!
__________________
Custom red anno Proto PM6 w/ UL frame, Lucky board w/ red eyes, CCM feedneck w/ Sundragon lever-lock Dust black Dye DM7 w/ Virtue board, blue laser eyes, CP flow plug, CP rake trigger
|
|
#5
02-12-2007, 03:12 PM
|
||||
|
||||
|
Re: What happened?
If you endup having to pull the valve pin and the cupseal looks fine you might have an o-ring on the valve that's gone bad.
I just thought of something, did you take your trigger frame off while you where installing the t-board by chance? If you, did you tighten the valve retaining screw?
__________________
Never go Bear hunting without a sandwich...sandwich: someone you can out run or don't mind shooting Angel 1 Non-SOM Apr 07 Ripper 3 Non-SOM Apr 08 Family Photo My Feedback
|
|
#6
02-12-2007, 03:17 PM
|
||||
|
||||
|
Re: What happened?
Must've been a little dry...the oil in the ASA solved the problem...as far as I can tell. Once I get a little more free time later tonight I will run some more T-balls through it again.
__________________
Custom red anno Proto PM6 w/ UL frame, Lucky board w/ red eyes, CCM feedneck w/ Sundragon lever-lock Dust black Dye DM7 w/ Virtue board, blue laser eyes, CP flow plug, CP rake trigger
|
 |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
