|
|
#1
12-29-2006, 10:57 AM
|
|||
|
|||
Feedneck problem
While pulling my hopper off today, I accidently spun my twist clamp too loose and it came off... without the c-clip, wich remained stuck inside the feedneck itself. I pulled it out, but I can't figure out how to connect it back into the twist clamp (it doesn't really fit and I'm afraid to try and squeeze it and force it in cause it seems like I might bend it up). I tried just sticking the c-clip in the neck and putting the twist clamp on over it, and that'll work to hold a hopper, but when I pull the hopper off the c-clip stays all the way tightened down in the feedneck.
So basically my question, for those who didn't feel like reading my long and pointless story, what's the trick to getting the c-clip and the twist clamp back together properly?
__________________
Marker Setup: Spyder VS2 stock eVLution II Hopper Java 68/4500 tank 
|
|
#2
12-29-2006, 11:00 AM
|
|||
|
|||
|
Re: Feedneck problem
Scratch that, answered my own question... just squeezed the clip and slid it up through the twist clamp and it popped right in... maybe I'm babying this thing too much.
__________________
Marker Setup: Spyder VS2 stock eVLution II Hopper Java 68/4500 tank
|
|
#3
12-29-2006, 03:18 PM
|
|||
|
|||
|
Re: Feedneck problem
awww I was gonna answer you but you had already posted
__________________
Having Vs problems/Questions Click me
|
|
#4
12-29-2006, 08:18 PM
|
|||
|
|||
|
Re: Feedneck problem
here's one for ya... how do I get the darned feed neck itself off? Does it just unscrew?
__________________
Marker Setup: Spyder VS2 stock eVLution II Hopper Java 68/4500 tank
|
|
#5
12-29-2006, 08:44 PM
|
||||
|
||||
|
Re: Feedneck problem
Yesssirrr
[the entire darn feedneck just twists right off the gun] although this has become a problem for me because once i took the whole thing off i can't screw it back in tight enough to stay because when i tighten my hopper down in it with the c clip the entire feedneck now twists while the hopper is in it! what do i do now? i would really like to get an entirely new feedneck altogether. and i hear it is ion/impulse threaded?
|
|
#6
12-30-2006, 01:28 PM
|
|||
|
|||
|
Re: Feedneck problem
yeah it is I had that problem too I just tightened it with a box wrench though
__________________
Having Vs problems/Questions Click me
|
|
#7
12-30-2006, 02:46 PM
|
||||
|
||||
|
Re: Feedneck problem
Loctite is God, when threads are concerned -
__________________
 KUSA Old School Alumni #4939Registered: 6/26/02 Posts: 14,000+ before the old mothership went down Jealousy is the tribute mediocrity pays to genius while feeling alone apposed to smiling adversaries.... 
|
|
#8
12-30-2006, 06:22 PM
|
||||
|
||||
|
Re: Feedneck problem
ohh definatly good idea!
butt i think im going to et a new one anyway kuz i heard that its ion/impulse threaded what kind should i get if i were looking at a new feedneck?
|
|
#9
12-30-2006, 06:54 PM
|
||||
|
||||
|
Re: Feedneck problem
CCM of course. I have them on almost all my markers. Clean all threads completely and use red Loctite. Let it cure -
__________________
KUSA Old School Alumni #4939Registered: 6/26/02 Posts: 14,000+ before the old mothership went down Jealousy is the tribute mediocrity pays to genius while feeling alone apposed to smiling adversaries....
|
|
#10
01-01-2007, 08:49 AM
|
||||
|
||||
|
Re: Feedneck problem
I have a CCM no-pro on mine and I love it. The stock feedneck was a ***** to get off.
|
 |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
