|
|
#11
12-06-2006, 06:09 PM
|
||||
|
||||
Re: chopped a ball, really need help with the cocking bolt
If you have an ACS bolt you don't want to oil it. The ACS bolts are delrin and if you put oil on delrin it will swell and cause recocking issues.
__________________
Almost finished LP Pilot <<XX PILOT OWNERS CLUB # 36 XX>> The Official Manual Thread Spyder Feedback PBN Feedback 
|
|
#12
12-06-2006, 06:15 PM
|
||||
|
||||
|
Re: chopped a ball, really need help with the cocking bolt
I oiled my ACS with no problems, but its probably better to avoid it. Only low grade delrin will swell with oil, but knowing kingman they might use different types each time...
__________________
05 Imagine Palmer stabilizer Maddman Rocket valve Trinity Front block IPS Sunbear Bolt Dark Horizon titanium striker Green/silver VSC CCI Phantom Red/Black PMR SE
|
|
#13
12-06-2006, 06:17 PM
|
||||
|
||||
|
Re: chopped a ball, really need help with the cocking bolt
Yea, it's probably hit or miss, but I would avoid it if possible.
__________________
Almost finished LP Pilot <<XX PILOT OWNERS CLUB # 36 XX>> The Official Manual Thread Spyder Feedback PBN Feedback
|
|
#14
12-09-2006, 08:03 AM
|
||||
|
||||
|
Re: chopped a ball, really need help with the cocking bolt
ok, is there anything else i should oil?
|
|
#15
12-09-2006, 08:36 AM
|
||||
|
||||
|
Re: chopped a ball, really need help with the cocking bolt
Just the striker. And if you haven't already, wouldn't be a bad idea to break the gun down and make sure everything is clean.
__________________
05 Imagine Palmer stabilizer Maddman Rocket valve Trinity Front block IPS Sunbear Bolt Dark Horizon titanium striker Green/silver VSC CCI Phantom Red/Black PMR SE
|
|
#16
12-09-2006, 08:42 AM
|
||||
|
||||
|
Re: chopped a ball, really need help with the cocking bolt
i have cleaned it out. ive cleaned it twice, when i chopped a couple of balls. the striker is the thing in the lower tube right under the bolt, right? and do i just oil the o-ring, or the whole thing?
|
|
#17
12-09-2006, 09:10 AM
|
||||
|
||||
|
Re: chopped a ball, really need help with the cocking bolt
Yes that is the striker, make sure you are using a paintball oil, and put a few drops on the oring it doesnt really hurt to spread it out a bit over the rest of the striker but isnt necesary.
__________________
 "If society is tranquil, it is not because it is conscious of its strength and its well-being, but because it fears its weakness and its infirmities; a single effort may cost it its life. Everyone feels the evil, but no one has courage or energy enough to seek the cure."
|
|
#18
12-09-2006, 01:23 PM
|
|||
|
|||
|
Re: chopped a ball, really need help with the cocking bolt
this happend to me oil up the gun and clean it out and you should be fine
|
|
#19
12-09-2006, 03:25 PM
|
||||
|
||||
|
Re: chopped a ball, really need help with the cocking bolt
yeah, its not doing it anymore
|
|
#20
12-10-2006, 08:16 PM
|
|||
|
|||
|
Re: chopped a ball, really need help with the cocking bolt
oiling your gun is important and very cheap as a little oil goes a long way. see if your field you play at sells any make sure it is for paintball markers. Gold Cup is a name to look for. if you brake a ball in a game you can pull a squeejee through the feed neck and the barrel or just unscrew the barrel and run it just through the barrel. after you are done playing for the day then brake down the gun and clean individual parts, the pilot is easy to due.
|
 |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
