Spyder Forums  

Go Back   Spyder Forums > Spyder Markers > Discontinued Markers
FAQ Members List Calendar Search Today's Posts Mark Forums Read

Reply
 
Thread Tools Display Modes
  #11  
Old 12-03-2006, 01:28 PM
Theheroguy Theheroguy is offline
Spyder Addict
 
Join Date: Aug 2006
Posts: 1,046
Default Re: My experiences with vs2 and how to fix everything so far

cleanthe striker rubber thingy and spring
Reply With Quote
  #12  
Old 12-03-2006, 02:03 PM
Hob Hayward's Avatar
Hob Hayward Hob Hayward is offline
not a nublet, sheesh.
 
Join Date: Feb 2006
Location: MA
Posts: 2,848
Default Re: My experiences with vs2 and how to fix everything so far

Its generally a good idea to make sure that everythings cleaned and lubed when somethings not working right. I actually strip my gun down the entire way, and run water through the body quite frequently, in fact after any day of play in which I chop.
__________________
05 Imagine
Palmer stabilizer
Maddman Rocket valve
Trinity Front block
IPS Sunbear Bolt
Dark Horizon titanium striker

Green/silver VSC CCI Phantom

Red/Black PMR SE
Reply With Quote
  #13  
Old 12-03-2006, 04:49 PM
scpres1 scpres1 is offline
Gangsta!
 
Join Date: Oct 2006
Location: Oregon
Posts: 59
Default Re: My experiences with vs2 and how to fix everything so far

Whats a good PSI, to run my VS2 at?
__________________
-Spyder VS2
-Red VS2 Accents
-Freak Barrel Kit
-Halo Rip Drive Hopper
-Pure Energy 3000 PSI Air Tank
-Dye Invision Mask
-Dye Barrel Condom
Reply With Quote
  #14  
Old 12-03-2006, 05:07 PM
bigred76's Avatar
bigred76 bigred76 is offline
Resident *******
 
Join Date: Dec 2005
Location: San Jose, CA
Posts: 6,228
Default Re: My experiences with vs2 and how to fix everything so far

I'd say about 250psi-ish.
__________________
SOC (+41, -0) | PBN (+12, -0) | New PBN (+20, -0)

URT... Ultimate Resource Thread!

The [OFFICIAL] Manual Thread!

BigRed Photography

Quote:
Originally Posted by Muddy Taco
ya my vagina hurts sometimes to
Reply With Quote
  #15  
Old 12-30-2006, 09:55 PM
Warthog Warthog is offline
New Guy
 
Join Date: Nov 2006
Posts: 10
Default Re: My experiences with vs2 and how to fix everything so far

add that recocking prolems could also be because of to High pressure, such as the spring does not have enought strength to move the cup seal, this problem happend to me when i was using co2 when it was very cold out, some liquid co got into my gun, spiked the guns psi to where the gauge needle was hitting the "R" in "Spyder" on the gauge.
Reply With Quote
  #16  
Old 01-28-2007, 06:29 AM
68vs2 68vs2 is offline
New Guy
 
Join Date: Dec 2006
Posts: 9
Cool Re: My experiences with vs2 and how to fix everything so far

having recocking issues..... try shaving some rubber off the ball detents...I guess when the gun is new, the rubber ball detents rub on the bolt and restrict it from moving freely...first cock the gun slowly and feel if in fact your ball detents are rubbing on the bolt....just make sure that you do not cut too much or your paintballs will roll out of your barrel.....peace
Reply With Quote
  #17  
Old 03-15-2007, 06:39 AM
OOB OOB is offline
lawl
 
Join Date: Oct 2006
Posts: 70
Default Re: My experiences with vs2 and how to fix everything so far

The air leaking down the barrel is not in the list.

--The reason (at least for me) is that my balance valve was not soo balance. It couldn't move fully to the "closed" position to stop the air flow through the barrel.

This is very simple to fix. I took apart everything and took out the valve. I noticed the valve pin didnt move very well even though it was covered oil lube from the factory. So I cleaned off all the oil/lube that was on it and reapplied oil/lube to it. Make sure to get some inside the valve because there are a few small o-rings in side or take it apart and lube them directly(probably not needed). After it was lubed/oiled the valve seemed more smother in its movement. Put everything back together and all was well.

I shot a few times and it seemed to be working. Couldnt try it more because my dog was freaking out cause i was firing inside (Also not recommended =P ).

NOTE: I cant wait to get out and actually shoot over a crono because from dryfireing and playing around in the back yard everything runs pretty smooth at about 225psi. I just have no idea what my fps. =P
Reply With Quote
  #18  
Old 05-05-2007, 05:13 AM
woodballvs3's Avatar
woodballvs3 woodballvs3 is offline
Everyone should own atleast 1 spyder
 
Join Date: Feb 2007
Posts: 40
Default Re: My experiences with vs2 and how to fix everything so far

Also are you useng a HPA tank and not a LPA tank? a low pressure tank that has an output of (i think 250-300?) wich has a lower recharge rate. I always use HPA wich has an output of 850 wich will supply any LP gun (just make shure u hav a reg LOL)
Reply With Quote
  #19  
Old 05-05-2007, 07:41 AM
woodballvs3's Avatar
woodballvs3 woodballvs3 is offline
Everyone should own atleast 1 spyder
 
Join Date: Feb 2007
Posts: 40
Default Re: My experiences with vs2 and how to fix everything so far

Quote:
Originally Posted by Dilatedug
hey have any of u ever had teh problem of when u are rocking it sweetly ..an then it goes below the opperating pressure and it no longer cocks. un til u cock it again..this had happend to me several times and idk wat to do about it ...i riased th pressure but it still happens evry so often..any tips?

Well if ur reg isnt broken in it might be that. or if your running A LPA tank at only 450psi it might be shootdown.
Reply With Quote
  #20  
Old 01-05-2008, 06:19 AM
KalypZo's Avatar
KalypZo KalypZo is offline
░-SpYdeR-░
 
Join Date: Jan 2008
Location: Long Island, NY
Posts: 16
Default Re: My experiences with vs2 and how to fix everything so far

When I shoot my bolt goes back in and I have to keep cocking it back to shoot and it doesnt go very far. Please help me!
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -8. The time now is 05:23 PM.