|
|
#1
10-21-2006, 08:19 AM
|
|||
|
|||
Helppppppppppppp
i had to disassemble my vs3 because the vertical adapter was loose. so i finally got it tighteng,but then i said let me try taking out the bolt. so i pulled the bolt back and lifted up, and then a small medal ball rolled out. i was lookin int hemanual and couldnt find this little ball. what the hell did i do? help
 
|
|
#2
10-21-2006, 08:49 AM
|
||||
|
||||
|
Re: Helppppppppppppp
Hrm, I dunno where there would be a metal ball in a spyder, perhaps leave it out and see what happens?
__________________
05 Imagine Palmer stabilizer Maddman Rocket valve Trinity Front block IPS Sunbear Bolt Dark Horizon titanium striker Green/silver VSC CCI Phantom Red/Black PMR SE
|
|
#3
10-21-2006, 08:58 AM
|
||||
|
||||
|
Re: Helppppppppppppp
maybe that was the problem?
besides the VA
__________________
Quote:
|
|
#4
10-21-2006, 09:21 AM
|
||||
|
||||
|
Re: Helppppppppppppp
Sounds like the tension ball in the bolt that holds the cocking pin in place...
What do you see down the hole in the bolt where the pin goes?
__________________
Angels, Timmys, ICD Bushy, Pimp, and lots of Spyders Old Farts Club
Member #12        "Your marker cannot harm me...I'm the Juggernaut!!" KUSA Feedback +56/-0 New PBN Feedback +20/-0 Old PBN Feedback +92/-0
|
|
#5
10-21-2006, 09:34 AM
|
||||
|
||||
|
Re: Helppppppppppppp
Ding Ding Ding..i think jimmys right
__________________
Quote:
|
|
#7
10-21-2006, 10:07 AM
|
|||
|
|||
|
Re: Helppppppppppppp
www.agobor.com/spyder i have 2 pix in there. sorry they're not too clear
|
|
#8
10-21-2006, 10:17 AM
|
||||
|
||||
|
Re: Helppppppppppppp
That spring and ball belong inside the bolt...
They hold the cocking pin in.... Did you take that screw out of the back of the bolt?
__________________
Angels, Timmys, ICD Bushy, Pimp, and lots of Spyders Old Farts Club
Member #12 "Your marker cannot harm me...I'm the Juggernaut!!" KUSA Feedback +56/-0 New PBN Feedback +20/-0 Old PBN Feedback +92/-0
|
|
#9
10-21-2006, 10:19 AM
|
|||
|
|||
|
Re: Helppppppppppppp
Quote:
|
|
#10
10-21-2006, 10:22 AM
|
||||
|
||||
|
Re: Helppppppppppppp
If the ball goes right thru the hole...the bolt needs to be replaced...
You could put the bolt and pin back in the marker and then put the ball, spring and screw in from the back.....
__________________
Angels, Timmys, ICD Bushy, Pimp, and lots of Spyders Old Farts Club
Member #12 "Your marker cannot harm me...I'm the Juggernaut!!" KUSA Feedback +56/-0 New PBN Feedback +20/-0 Old PBN Feedback +92/-0
|
 |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
