|
|
#11
09-24-2006, 04:54 PM
|
||||
|
||||
Re: Dented barrel
Well, if yours is black it should be fine, they cleared up pretty quickly.
I don't think they have an MR1 anti-chop bolt yet...
__________________
05 Imagine Palmer stabilizer Maddman Rocket valve Trinity Front block IPS Sunbear Bolt Dark Horizon titanium striker Green/silver VSC CCI Phantom Red/Black PMR SE 
|
|
#13
09-25-2006, 06:03 AM
|
|||
|
|||
|
Re: Dented barrel
I think the bolt inside the MR1 is an ACS bolt, and it stand for Anti Chop System, so i dont think it will change anything to have it replaced. I have seen people who played with internal parts too many times and they messed up the ball detent. Use an expansion chamber or/and a remote coil, maybe the 6 round burst will have enough constant gaz to operate correctly.
|
|
#14
09-25-2006, 11:31 AM
|
|||
|
|||
|
Re: Dented barrel
Quote:
I use HPA for all my markers because I find that Co2 is quite inconsistent and also you can't use it when its cold outside. And at some fields, HPA refills are cheaper than Co2!
__________________
Click here to see my SpecOps Brigade Profile!
|
|
#16
09-25-2006, 05:28 PM
|
|||
|
|||
|
Re: Dented barrel
Word of advice , don't get the ACS bolt. BTW what e-grip do you have? Because I have had no problem on my mr-1 with a RTF 2.0 so I was just curious.
|
|
#17
09-26-2006, 10:59 AM
|
|||
|
|||
|
Re: Dented barrel
They're a rubber thing that holds the ball in place and stops the gun from double feeding.They are about a couple of bucks for another one,If you take the feed neck off they is a small circle located by the bottom screw.Pull it out and see if it's broken if it's not broken it should like this:http://www.firstcallpaintball.com/pa...ll-detent.html
__________________
MR1- -Nightstick 14" barrel -Viewloader Evo II Hopper -Spyder Rocking Trigger
|
|
#18
09-26-2006, 11:09 AM
|
||||
|
||||
|
Re: Dented barrel
I'm almost positive uoit problem is that either your outshooting the co2 tank (very easy to do) or that you need to lube the internals. Polishing the internals would also help with recocking.www.ottersccustoms.com
Did you try shooting straight up with no balls in the hopper?
__________________
05 Imagine Palmer stabilizer Maddman Rocket valve Trinity Front block IPS Sunbear Bolt Dark Horizon titanium striker Green/silver VSC CCI Phantom Red/Black PMR SE
|
|
#19
10-02-2006, 09:59 AM
|
|||
|
|||
|
Re: Dented barrel
Ok....new update.
Refilled my tank...lubed the hell out of the MR1. semi, and 3 round are ok. 6 round is ok for a few pulls of the trigger, then chops the balls again. Full auto...chops like crazy. I think you guys are right, and I am outshooting the co2. Avenged Sevenfold....the grip is from an Imagine. The hopper is a revolution w/x-board....suppose to do 12 bps. I put the original grip frame back on it today...tired of messing with it. My next step is to try different paintballs. If that dosent work, going to sell the e-grip and keep it stock. LEOinFL
|
|
#20
01-26-2007, 08:46 PM
|
|||
|
|||
|
Re: Dented barrel
its easy, the problem is the stock fire rate which is 13 i believe is way too high. you need to get a faster loader, when you shoot more than 6 balls it always gonna chop. i had the same problem, but it was my e-grip.
Please stop posting in these old threads. jjr
|
 |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
