more T-board issues...

[aodsnyper]

that's kind of what i've been thinking.

but then why does the stock board work and not the T-board. i can crank on the stock board all day and cap it out w/out it double firing once. it worked with my Classic and my BLM. it's just the T-board where i have issues and that doesn't make sense.

i need to switch my frame to my Classic and see what happens. won't be tonight though. i'll keep you posted.

thx for all the input,
justin

[adrianm1188]

Didnt read the stock board part... Hmm. I've never tried my stock board on my BLM. I think i might do that.

If the stock board works, then its definetly the settings on the T-Board.
Try Lowering your Dwell and raise your Debounce.

*Anyone else, feel free to correct me on the settings thing. *cough* Dragon

[aodsnyper]

if i go with a lower dwell than 5, (w/o air) you can hear the sear wanting to "double fire". it has a weak sound to it. all my testing is using a fully charged Java 9.6. and a debounce of 15+ i think should be high enough to extinguish a bounce issue. but the occasional double firing still occured.

i think i'm going to get a little wild with the sandpaper and dremel this week. i might take a little more off the frame and maybe notch out the BLM so the frame actually sits in the receiver. i don't know yet.

justin

[adrianm1188]

Talk to Damon before you start cutting/grinding.

Maybe the capacitator is weak. Not giving enough energy to the solenoid

[aodsnyper]

one might think that, but it's only when i change the settings. i think the cap. is still good. if it's default, it's fine...


okay, how about i explain it like this:

default settings; sounds great (no air). everything sounds solid, not missing a beat.

go into setup (put in factory "default" settings); sounds different than actuall "defualt".

does that make sense..? they don't sound the same, when in actuality, they should be no different at all?

i have 3 BLM bodies, so i figure i could test on one of them. i got one for free in a trade, it's pretty "modified", looks wise. looks like poop, but it should serve as a test dummy.

justin

[aodsnyper]

well, i've gotten close. i've got a dwell of 5 and a debounce of 25 and things seem to be going okay. i've only dry fired, no balls yet. i don't want to have to clean this thing if it doesn't work out ya know. i haven't done any sanding/dremmeling either. think i'm going to do just a bit though... because every so often, at high rates of fire, i still have the occasional "not fully cocking" issue. but with a ball, this might go away.

i was also wondering, if i have my debounce up to 25, is that going to affect my firing rate? if not, i'd almost go to 50 or so and just leave it.

thx,
justin

[adrianm1188]

100ms = 10bps. <-- otters site

T-Board Tutorial

[aodsnyper]

great! thx again adrian...

so then 50ms = 20bps, right. and then 75 ms = 15 bps. if so, why wouldn't everyone have it set there? that would cap it at 15 bps. i think i'll do that if that's the case.

in a sense, if a tourny only allowed 15 bps (which most do) either ramping or not... this would automatically have the board set at 15 bps (75 ms debouce), right? regardless or not if i had the ramping chip.

justin

[aodsnyper]

so i just installed the Ramping chip becuase we get to use PSP to 15bps in this next tourny. i'm a little confused on how to get this setup correctly.

i know how to do "Setup 1", but it's the crossover to "Setup 2" that i can't quite figure out. do i need to shut off the frame after completing "Setup 1" and then go in to "Setup 2?" the manual reads a little funny and i can't get my frame to act the same way the manual says to do it.

any help is appreciated as always.

thx,
justin

[covert24]

yup had the same exact problem. just explian ur problem a little better.