whats your lp setup

[Heroguy]

what is it and how much did it cost what marker do you have

whats your bottom pressure

no I don't want to go to otter customs I've already been

[vwjimmy]

I read something awesome once...
"Low Pressure is a side effect, not a goal"
That doesn't effect my attempts to go lower though....
Pilot
Sunbear Bolt
Nightstriker
NDZ Valve
Bob Long Torpedo
Trinity -15* V/A
32* Spring Kit
Plus lots of other stuff unreleated to pressure....
Runs a 260psi 285fps with a stock delrin ACS on HPA...
I haven't tuned the Sunbear yet
As for the cost....way too much!!!

[ooglieboogliebob]

Marker: Spyder TL-X
Barrel: Dye UL 14"
Feedneck: Trinity T-lock Clamping Feedneck
Hopper: Zeggy
V/A: 15* High-Flow Assault Block (dremeled out some) and 1200psi 32* gauge
Regulator: Bob Long Torpedo
Drop Forward/ASA: North West (NW) Drop forward with on/off and DYE 1,500psi gauge
Trigger Frame: IPI 2.0 with Stock Modded trigger, and 50g switch
Internals: Otterized bolt and striker (polished and venturi removed), NDZ Valve
Operating Pressure: 225psi@~275fps

Edited for some mistakes

[druid]

Marker: Spyder Esprit (bought new in player's pack)
Barrel: J&J Ceramic 14" - $25 used
Feedneck: ShockTech - $35 new
Hopper: Z egg - $45 new
V/A: -10* High-Flow Trinity VA (dremeled out) and 600psi BL gauge - $40 new
Low Pressure Chamber: 5" Shocktech - $15 used
Regulator: Bob Long Torpedo - $35 used
Drop Forward/ASA: 32* Flame and Unimount - $30 used
Trigger Frame: Boo*Yaah frame, TBoard w/ BB eyes, 50g switch - $110 complete
Internals: Superfly bolt and NightStriker XL, Rocket Valve, Maddman Spring Kit - $30 new
Operating Pressure: 200psi@~279fps

[vikingshadow]

Marker- Old Style Sonix
Barrel- 14" 32* Night Stick and 14" J&J Ceramic with porting taped up
Feedneck- It has the crappy powerfeed so a plastic elbow - BOO! Did help with blowback into the loader though.
V/A-CIP Assault Block with 32* 0-600 guage
Loader- Zeggy (Z boarded eVlution)
Regulator- Bob Long Torpedo
ASA and Drop- CIP Medium with on/off
Frame- ESP IPI modified with response trigger and super light microswitch
Valve- Maddman Rocket valve
Springkit- Shocktech
Striker- modified, polished
Bolt- modified, polished
Operating pressure- 200-220 psi @ 280 fps (it was several years ago so really hard to remember.) Also got approxiamately 2000 shots off a 20 oz Co2 tank back when I was still using it. Took a LOT of tuning of the valve and springs, and quite some time to do it.

Sidenote: The "low pressure is a side affect, not a goal" came from Chris Cole's signature and was a topic for huge debate for a long time. Personally, I think it's a matter of semantics. It's not a side effect if that was your goal to begin with - the parts are needed to take it down that low, obviously, yet if you were to add them anyway without LP as your goal, the pressure would lower still. LP is acheived whether you want it or not with certain parts - see the quandry? I think that if you did it on accident - then it's a side effect. If you did it on purpose, then it's a goal.

Ok, enough of that - back to the regularly scheduled re-runs....

[shunut]

Marker: TLX
Barrel: Dye Aluminium Barrel
Feedneck: NDZ Pro Lock
Hopper: Halo B w/rip drive
V/A: Bob Long/32 Degrees VA w/LPC
Regulator: Bob Long Torpedo
Drop Forward/ASA: CP Razor Drop w/ CP On/Off ASA
Trigger Frame: ESP frame, TBoard w/ BB eyes, 50g switch, custom one of a kind delrin trigger.
Internals: Kingman ACS Delrin Bolt and DH Titanium Striker, Rocket Valve, Maddman Spring Kit
Operating Pressure: 240psi@~285fps

[bamf-hacker]

I parted out my LP Rodeo, but this was her set up

Marker- Green Rodeo
Barrel- 14" J&J ceramic, 14" & 16" CP 2 piece kit, 14" & 16" Full Freak
Feedneck- Hybrid Clamping feedneck
V/A-CIP Assault Block with Dye 0-800 guage
Loader- Halo B w/rip and a Z boarded eVlution
Regulator- CP Long Reg no gauge
ASA and Drop- CP Razor drop and 2k5 ASA w/bleed
Frame- C.A.M.D. ESP frame
Valve- AKA Tornado Valve
Springkit- Shocktech Springs and Shim kit
Striker- DH Otterized Striker
Bolt- ACS Delrin Bolt (I has no issues with it)
Operating pressure- 250 psi @ 285 fps

[Heroguy]

oh snap!!! thats alot of people
thanks guys

[Eaglelox]

Marker: imagine
Barrel: jj
Feedneck: trinity
Hopper: Halo B w/rip drive victory
V/A: modded
Regulator: Bob Long Torpedo
Trigger Frame: ESP frame, TBoard w/ BB eyes, no trigger spring
Internals: Sunbear Bolt and Nightstriker, modded tornado Valve, 32 Spring Kit
Operating Pressure: 350 psi, 300 fps

[vwjimmy]

Eaglelox...why would you run a Sunbear and Nightstriker??? LOL!!!!