|
|
#1
08-10-2008, 05:41 PM
|
||||
|
||||
Air issues
Ok problem:my MR2 with eye is having serious air isues I shoot then it burps like its out of air. I turn the velocity up a little bit and shout 50 RNDs or so and then it does it again. Striker ring is fine I havnt had this trouble with a cup seal before, could it be that? anyway im looking for a diferent aproch or angle to this question so what do you think the problem could be?
EDIT: I use HPA as well as a remote, tried it without the remote same problems. It was hot out and velocities were all over the place even with HPA.
__________________
General Shawn Wayne Tetz, Commander 187th Gaurds Mechanized Rilfe Division. - Includes the 3rd armored brigade from the 34th Gaurds Armored Division. (APC's and armor as well as support elements) -UCSF Armored Division Commander Armored Units -Deep insertion APC -Killer "B" Battle Tank -Troop Transport APC (almost done) -Gun Truck heavy support unit (In the works) -Order of Lenin (1st) -Skyline Sergeant -YGP Rep! -Sector 4 team feild honor recipiant (UCSF) 
|
|
#2
08-11-2008, 12:35 AM
|
|||
|
|||
|
Re: Air issues
Have you tried a diffrent air tank?
Possibly the regulator on the tank went for a shi* Ill try to think up some more possibilities here
|
|
#3
08-11-2008, 06:02 AM
|
||||
|
||||
|
Re: Air issues
Air tank worked fine on my MR1 afterwards.
__________________
General Shawn Wayne Tetz, Commander 187th Gaurds Mechanized Rilfe Division. - Includes the 3rd armored brigade from the 34th Gaurds Armored Division. (APC's and armor as well as support elements) -UCSF Armored Division Commander Armored Units -Deep insertion APC -Killer "B" Battle Tank -Troop Transport APC (almost done) -Gun Truck heavy support unit (In the works) -Order of Lenin (1st) -Skyline Sergeant -YGP Rep! -Sector 4 team feild honor recipiant (UCSF)
|
|
#4
08-11-2008, 06:32 PM
|
||||
|
||||
|
Re: Air issues
Got it figured out now thanks guys.
__________________
General Shawn Wayne Tetz, Commander 187th Gaurds Mechanized Rilfe Division. - Includes the 3rd armored brigade from the 34th Gaurds Armored Division. (APC's and armor as well as support elements) -UCSF Armored Division Commander Armored Units -Deep insertion APC -Killer "B" Battle Tank -Troop Transport APC (almost done) -Gun Truck heavy support unit (In the works) -Order of Lenin (1st) -Skyline Sergeant -YGP Rep! -Sector 4 team feild honor recipiant (UCSF)
|
|
#6
08-12-2008, 04:39 PM
|
||||
|
||||
|
Re: Air issues
Im not even sure i compleatly tore the whole gun appart, put a new striker ring oiled it good polished the pin took it out back and it worked great. i striped the launcher off too. Im gonna play without it a few times till im sure the marker is where I want it to be before I put it back on so I dont have the same problem and have to strip everything off again.
__________________
General Shawn Wayne Tetz, Commander 187th Gaurds Mechanized Rilfe Division. - Includes the 3rd armored brigade from the 34th Gaurds Armored Division. (APC's and armor as well as support elements) -UCSF Armored Division Commander Armored Units -Deep insertion APC -Killer "B" Battle Tank -Troop Transport APC (almost done) -Gun Truck heavy support unit (In the works) -Order of Lenin (1st) -Skyline Sergeant -YGP Rep! -Sector 4 team feild honor recipiant (UCSF)
|
 |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
