Spyder Forums  

Go Back   Spyder Forums > General Spyder Discussion > Veteran Forum
FAQ Members List Calendar Search Today's Posts Mark Forums Read

Reply
 
Thread Tools Display Modes
  #1  
Old 12-29-2005, 03:27 PM
Drefish99's Avatar
Drefish99 Drefish99 is offline
Weeeee!
 
Join Date: Dec 1969
Location: NOR*CHI
Posts: 1,982
Default Warpedmephisto Angel ACE install and dual detent milling

I posted this up on the Nation and wanted to share it with my KUSA friends.

A few weeks ago I contacted Warpedmephisto as I caught wind that he did ACE milling and installation for a really reasonable price. When I saw some pics of his work on his site - http://www.warpedairsmithing.com/ I wanted to support a fellow moderator brother. After contacting him he acknowledged that he did self ACE installs also as a service. The way it works is you acquire the board and eyes setup (Timmy, DM, Predator, etc.) and he will do all the milling and prep work for you and you do the actual install and setup. I had a pretty good knowledge or setting up eye systems as I have done them in the past on other blind guns (Spyders, Imps, BKO’s). I figured I could do the work on my Angel and since it was my newly acquired baby I wanted it milled professionally instead of me using a Dremel and a drill press.

I sent my gutted body and frame out to him and in a quick turn around it was back at my house and ready for me to put back together. I shipped about a week ago and I received the finished product yesterday. Then again we both live in the same state just 3 to 4 hrs away.

Now some pics of the work.


Left side of the stock detent, the newly drilled eye hole and drilled and tapped Eclipse eye cover screw hole.


Right side the newly drilled 2nd detent and same eye setup as left


Perfectly aligned eye holes minimize eye troubles from poorly aligned eyes.


Special effects with a flashlight Ohhhh!!!


Bottom was sealed


Bottom Eye wire milling


Custom switch plate to hold the new switch.

As a lower cost alternative to adding ACE on to an older Angel I see this as a great alternative. As more and more boards are being replaced by faster boards people are letting go their older outdated boards cheaper and cheaper. His work as you can see is top notch and should be a great choice. Once I get it all together again I’ll post up some pics.
__________________
Romans 6:23
“God never promises to remove us from our struggles. He does promise, however, to change the way we look at them.”-Max Lucado
The most he did was die for me, the least I can do is live for him.
Reply With Quote
  #2  
Old 12-29-2005, 03:42 PM
vikingshadow's Avatar
vikingshadow vikingshadow is offline
Ah-roo! Ah-roo! Ah-roo!
 
Join Date: Dec 2005
Location: Where my stuff is. Duh!
Posts: 6,950
Default Re: Warpedmephisto Angel ACE install and dual detent milling

So, do you have to have to send the board, eyes and eye covers for him to do this, or does he just do the milling without all that stuff?
__________________
Pressing on
Never argue with an idiot; they'll drag you down to their level and beat you with experience." ~ Anonymous
Reply With Quote
  #3  
Old 12-29-2005, 03:52 PM
Drefish99's Avatar
Drefish99 Drefish99 is offline
Weeeee!
 
Join Date: Dec 1969
Location: NOR*CHI
Posts: 1,982
Default Re: Warpedmephisto Angel ACE install and dual detent milling

Nope all he needed to know was what size eyes I was going to use. Either the 3mm or the 5mm and for a few extra bucks he supplied the Eclipse covers and supplied the screws too.
__________________
Romans 6:23
“God never promises to remove us from our struggles. He does promise, however, to change the way we look at them.”-Max Lucado
The most he did was die for me, the least I can do is live for him.
Reply With Quote
  #4  
Old 12-29-2005, 04:26 PM
vikingshadow's Avatar
vikingshadow vikingshadow is offline
Ah-roo! Ah-roo! Ah-roo!
 
Join Date: Dec 2005
Location: Where my stuff is. Duh!
Posts: 6,950
Default Re: Warpedmephisto Angel ACE install and dual detent milling

Cool! The sensei thing is kinda throwing my mind in a tizzy right now, and I think I'd rather have eyes.

Did you notice advantagepb is developing an Angel board?

Which brings me to my next question....can any aftermarket board that will accept eyes work on any Angel? I'm thinking of using this guy to mill my gun for me, but not until I have the stuff for it...
__________________
Pressing on
Never argue with an idiot; they'll drag you down to their level and beat you with experience." ~ Anonymous
Reply With Quote
  #5  
Old 12-29-2005, 04:33 PM
Drefish99's Avatar
Drefish99 Drefish99 is offline
Weeeee!
 
Join Date: Dec 1969
Location: NOR*CHI
Posts: 1,982
Default Re: Warpedmephisto Angel ACE install and dual detent milling

Pretty much anything that can activate the solinoid can work with this upgrade. Many use Intimidator boards for their cost. He provides the switch plate that you can use to mount the new microswitch. I believe the new Angel Advantage boards will be a lot better as they will fully fit in your frame and best thing is the controls will be accessable from the buttons behind the frame in the stock locations.
__________________
Romans 6:23
“God never promises to remove us from our struggles. He does promise, however, to change the way we look at them.”-Max Lucado
The most he did was die for me, the least I can do is live for him.
Reply With Quote
  #6  
Old 12-29-2005, 05:09 PM
bamf-hacker's Avatar
bamf-hacker bamf-hacker is offline
Bling Bling Bling
 
Join Date: Dec 2005
Location: In your PC...
Posts: 5,941
Default Re: Warpedmephisto Angel ACE install and dual detent milling

So I could send in my Spyder body to get is milled for eyes? I want a t-board with eyes, but don't want to hose my marker if I drill it bad.

HacKeR
__________________
Quote:
Originally Posted by TheRedBarron
secks comes to mind everytime I look at those markers. pure freaky secks.

Trust
*AO*IO*KUSA*PBN*PHOG*
You have been roshamboed
BAMF-Hacker's Mood: HAPPY HAPPY HAPPY!!!!
Reply With Quote
  #7  
Old 12-29-2005, 05:15 PM
Drefish99's Avatar
Drefish99 Drefish99 is offline
Weeeee!
 
Join Date: Dec 1969
Location: NOR*CHI
Posts: 1,982
Default Re: Warpedmephisto Angel ACE install and dual detent milling

If it is a Spyder I highly recommend The Trooper. He is a fellow moderator with me on the Kingman section. He has done several of my Spyders and I love his work. I think Warp specializes in Angels. All in all tell both of them that I recommended you to contact them and I'm sure they will give you a pretty good rate.
__________________
Romans 6:23
“God never promises to remove us from our struggles. He does promise, however, to change the way we look at them.”-Max Lucado
The most he did was die for me, the least I can do is live for him.
Reply With Quote
  #8  
Old 12-29-2005, 05:16 PM
bamf-hacker's Avatar
bamf-hacker bamf-hacker is offline
Bling Bling Bling
 
Join Date: Dec 2005
Location: In your PC...
Posts: 5,941
Default Re: Warpedmephisto Angel ACE install and dual detent milling

Awesome..... I am looking to pick up the t-board soon so I will PM The Trooper to find out.. Thanks

HacKeR
__________________
Quote:
Originally Posted by TheRedBarron
secks comes to mind everytime I look at those markers. pure freaky secks.

Trust
*AO*IO*KUSA*PBN*PHOG*
You have been roshamboed
BAMF-Hacker's Mood: HAPPY HAPPY HAPPY!!!!
Reply With Quote
  #9  
Old 12-29-2005, 08:57 PM
TacTownKilla's Avatar
TacTownKilla TacTownKilla is offline
Listen to Bob Marley
 
Join Date: Dec 2005
Location: 253 fo lyfe
Posts: 656
Default Re: Warpedmephisto Angel ACE install and dual detent milling

Does the trooper still do eye milling? I heard awhile back that we stopped.
Reply With Quote
  #10  
Old 12-30-2005, 03:54 PM
Drefish99's Avatar
Drefish99 Drefish99 is offline
Weeeee!
 
Join Date: Dec 1969
Location: NOR*CHI
Posts: 1,982
Default Re: Warpedmephisto Angel ACE install and dual detent milling

The Trooper is a member here too. Just tell him that I send you and if he isn't busy will give you a better chance of him reconsidering his retirement.
__________________
Romans 6:23
“God never promises to remove us from our struggles. He does promise, however, to change the way we look at them.”-Max Lucado
The most he did was die for me, the least I can do is live for him.
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -8. The time now is 02:36 AM.