|
|
#11
05-31-2008, 08:26 AM
|
||||
|
||||
Re: Balls Falling Out Of Barrel
I checked the online diagram and made sure everything was in right. Also, when i plug in my tank, I get a large bust of air from my barrel for about 2 seconds.
Where can I find replacement detents? I dont even know what they look like. Ive never had to deal with this before. I just did a lil test. No air with paint in the hopper. I pull the bolt back and fire (pointing the gun towards the ground), 1 ball will come out. Normal????
__________________
My MR1 - 14" J&J Ceramic - Adjustable Car Stock - MR3 Rail w/ Riser - Archon Hopper - 3000psi Guerilla HPA - UPZ Remote - Tasco Red Dot Sight - Custom Made Suppressor Great Stuff Here http://www.freepaintballplans.com/forum/index.php Last edited by Zee : 05-31-2008 at 08:39 AM. 
|
|
#12
05-31-2008, 08:44 AM
|
||||
|
||||
|
Re: Balls Falling Out Of Barrel
Yes, that is normal. The bolt stills disengages the ball from the detent.
__________________
People crave what they don't have. Vid of me and my Guitar derek_owns_a_guerrilla_radio-School buses don't = target practice, Hoss..  Hossapher-i shot alot of different types MR1 Sniper Rifle Rocket Launcher
|
|
#13
05-31-2008, 10:43 AM
|
||||
|
||||
|
Re: Balls Falling Out Of Barrel
so the detent is still good, its probably just the leak.
Thanks for all the help
__________________
My MR1 - 14" J&J Ceramic - Adjustable Car Stock - MR3 Rail w/ Riser - Archon Hopper - 3000psi Guerilla HPA - UPZ Remote - Tasco Red Dot Sight - Custom Made Suppressor Great Stuff Here http://www.freepaintballplans.com/forum/index.php
|
|
#14
06-04-2008, 01:18 PM
|
||||
|
||||
|
Re: Balls Falling Out Of Barrel
OK so i fixed the leak, hooked up my HPA tank and fire......ball just rolls out of the barrel and then I have to recock the bolt. Whats the issue?
__________________
My MR1 - 14" J&J Ceramic - Adjustable Car Stock - MR3 Rail w/ Riser - Archon Hopper - 3000psi Guerilla HPA - UPZ Remote - Tasco Red Dot Sight - Custom Made Suppressor Great Stuff Here http://www.freepaintballplans.com/forum/index.php
|
|
#16
06-04-2008, 04:18 PM
|
||||
|
||||
|
Re: Balls Falling Out Of Barrel
I believe so, I took apart the gun twice now and followed the online diagram. I'm baffeled...
If a gun description says "Low pressure operation" does this mean that HPA is not supported?
__________________
My MR1 - 14" J&J Ceramic - Adjustable Car Stock - MR3 Rail w/ Riser - Archon Hopper - 3000psi Guerilla HPA - UPZ Remote - Tasco Red Dot Sight - Custom Made Suppressor Great Stuff Here http://www.freepaintballplans.com/forum/index.php Last edited by Zee : 06-04-2008 at 05:19 PM.
|
|
#17
06-04-2008, 05:44 PM
|
||||
|
||||
|
Re: Balls Falling Out Of Barrel
I don't know, that still sounds like the bolt's upside down. But, with the bolt not re-cocking....
__________________
Quote:
|
|
#18
06-04-2008, 05:56 PM
|
||||
|
||||
|
Re: Balls Falling Out Of Barrel
Ive tried both ways the bolt can go in...one way is worse than the other. I'd pull my hair out but I shaved it all off.
__________________
My MR1 - 14" J&J Ceramic - Adjustable Car Stock - MR3 Rail w/ Riser - Archon Hopper - 3000psi Guerilla HPA - UPZ Remote - Tasco Red Dot Sight - Custom Made Suppressor Great Stuff Here http://www.freepaintballplans.com/forum/index.php
|
|
#19
06-04-2008, 06:12 PM
|
||||
|
||||
|
Re: Balls Falling Out Of Barrel
yeah, the not cocking is throwing me off. is it the e-grip? check your battery if it is. It's a bit of a stretch in my mind, but you never no. It's one of the most common problems at our local field. People just don't ever think about it.
__________________
Quote:
|
|
#20
06-04-2008, 06:16 PM
|
||||
|
||||
|
Re: Balls Falling Out Of Barrel
scratch that, just briefly researched the gun and I couldn't find an electronic version.
__________________
Quote:
|
 |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
