|
|
#971
05-07-2010, 01:25 PM
|
||||
|
||||
Re: What cha Drivin
soak it in goo gone/any citrus based adhesive remover and then use a flat blade (razorblade?) to scrape it up. or a heat gun...
__________________
8/23/03 OS KUSA #10898
Spyder to pump conversion tutorial! Project LP Reposted! Sales Thread Feedback Quote:
- from Ray Bradbury's Something Wicked this Way Comes 
|
|
#972
05-07-2010, 05:51 PM
|
||||
|
||||
|
Re: What cha Drivin
i miss my volvo, sigh!!!
__________________
My Markers -Spyder TL Plus w/ 18 inch Opsgear Barrel -Spyder TLXtra (wife's)
|
|
#973
05-08-2010, 12:08 AM
|
||||
|
||||
|
Re: What cha Drivin
Just peel it off and use googone to get the residue off. A blade will most likely just scratch the clear coat and the paint. I wouldn't be worried about the residue left behind but if it's been there long enough, then the paint around it will have faded and you'd still be able to see the outline.
__________________
If you stand for nothing you will fall for anything.
|
|
#974
05-08-2010, 01:55 AM
|
||||
|
||||
|
Re: What cha Drivin
I'm worried about the ones on the paint, though. They've been there a really long time... I don't want to pull off paint too, ya know? I'll probably nab some 5.0 emblems for the sides where the skulls were to cover it up if it's bad enough.
__________________
SOC (+41, -0) | PBN (+12, -0) | New PBN (+20, -0) URT... Ultimate Resource Thread! The [OFFICIAL] Manual Thread! BigRed Photography Quote:
|
|
#975
05-08-2010, 03:43 AM
|
||||
|
||||
|
Re: What cha Drivin
Just use a hair dryer if you don't have a heat gun and get it nice and warm, just be careful. Slowly peel the sticker up while applying heat. Take your time and it should be fine.
Don't run out and buy goo gone or another adhesive remover if you don't already have any. You can use WD40, it's perfectly safe to use on your paint/clear. I just used WD40 to remove an octane rating sticker on the tank of my r6. You wouldn't be able to tell that there was a sticker there in the first place.
|
|
#976
05-08-2010, 05:44 PM
|
||||
|
||||
|
Re: What cha Drivin
Just pull it off, who gives a ****, it's meant to be abused.
__________________
If you stand for nothing you will fall for anything.
|
|
#977
05-09-2010, 12:51 PM
|
||||
|
||||
|
Re: What cha Drivin
is that a cobra or are those just wheels off one?
|
|
#978
05-09-2010, 02:19 PM
|
||||
|
||||
|
Re: What cha Drivin
Just a GT, but by the time I get done with it the lines of distinction will be null.
 the rims came with it, and there was some nice rubber put on it. 275's all around with Bridgestone Potenza Sports on the front and some brand new Sumitomo's on the rear.
__________________
SOC (+41, -0) | PBN (+12, -0) | New PBN (+20, -0) URT... Ultimate Resource Thread! The [OFFICIAL] Manual Thread! BigRed Photography Quote:
|
|
#979
05-11-2010, 01:17 AM
|
||||
|
||||
|
Re: What cha Drivin
Starting to order my turbo parts. ^_^ ordered some injectors off of a volvo 850t tonight and if this other guy has a turbine housing with a flat flange then I'll be buying a 15g turbo tomorrow.
__________________
If you stand for nothing you will fall for anything.
|
|
#980
05-13-2010, 02:26 PM
|
||||
|
||||
|
Re: What cha Drivin
Tim, 3M makes an adhesive remover that actually works. I use it on longboards when I do custom grip tape designs to remove the glue without hurting the finish. Any Advance Auto Parts should have them.
UK, painting the rims while they're on the vehicle still is a terrible idea. I hope you have to replace you pads and rotors soon.
__________________
N'Vasion Paintball | T-1 Project | MR1 Project | Feedback (+30,-0) | PBN Feedback (+34,-0) | Myspace | Better Sniping 101 Quote:
|
 |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
