Make your revy faster

[covert24]

Aight guys this is a very simply process to make your revy alot faster then if u jsut left it alone. This doesnt involve dremeling and modding anything just a simple proocess.

1. Unscrew all the front screws so you can get ahold of the servo, board, and eyes.

2. Disconnect the wires from the board and also from the eye board

3. Take out the servo so you are holding it upsidedown and u should see 4 screws on each corner.

4. Get a small screwdrive and unscrew those 4 screws.

5. The bottom part should be able to be jiggeled free and u should see the gears.

6. Get some WD-40 and spray alot of it in there.

7. Move the impeller around with your hand so all the WD-40 gets onto everything.

8. There should be a small pool of WD-40 still in the gearbox. Dump the excess into a sink.

9. Continue to move the impeller around with your hand.

10. Screw the 4 screws back into the servo and connect the wires back onto the board.

11. Make sure all the wires are not on any of the outside of the hopper so as not to get crinched inbetween the shells.

12. After making sure everything is in place put the top shell on and screw back together.

13. Get some batterys (dont have to be new) and put them in.

14. Turn the hopper on and let it run for about 2 minutes. It should turn off automatically.

15. Fill the hopper with paintballs and do a standard drop test and then let sit for a while.

16. Your revy will now be faster then it was stock because of the excess lubrication inside the gearbox. it also will run smoother then before.

If u want to sticky this that would be fantastic.

[QAZ123]

It still feed's at 12 bps as that is as fast as it can go.

JB.

[TheRedBarron]

Originally Posted by QAZ123

It still feed's at 12 bps as that is as fast as it can go.

JB.

QFT It is still limited to the speed of gravity.

[covert24]

it spins faster. so it agitates the paint more. so no clogs or jams

[TacTownKilla]

1 sell revvy
2 buy halo
3
4 profit

The only way ur gonna make your revvy feed faster tho is to buy a turbo board, but good luck with taht they are uber rare and expect to pay out the ass for one if you actually find one.

[Voodoo27909]

DO NOT DO NOT DO NOT Spray ANYTHING into a servo!!!!! There is an electronic circuit board in there, and WD 40 will EAT IT TO PIECES! You could go to a local hobby shop and buy a faster servo meant for RC applications,.....but after cost and labor you might as well go buy a faster loader.

DO NOT DO NOT DO NOT Spray ANYTHING into a servo!!!!!

[ooglieboogliebob]

yeah ... wd-40 is a bit abbrasive too ... tried it on my bearings on my skateboard before .. a few weeks later .. the balls were pretty much gone.

[druid]

this is how you make a revvy faster.....

1. Remove Revvy from marker
2. Set marker aside, take the Revvy out to the picnic table
3. Hang large tarp on washlines, making yourself a nice private work cubical
4. Insert Cherrybomb into feedneck and light
5. Run like Hell!!!!!

6. Buy Halo/Reloader

[ooglieboogliebob]

hahaha !!! nice ... i'd rather have the reloader b from those two choices ...

[splater18]

Originally Posted by druid

this is how you make a revvy faster.....

1. Remove Revvy from marker
2. Set marker aside, take the Revvy out to the picnic table
3. Hang large tarp on washlines, making yourself a nice private work cubical
4. Insert Cherrybomb into feedneck and light
5. Run like Hell!!!!!

6. Buy Halo/Reloader

yea do that but stick like 7 bottle rockets out of the feed neck and get fome lighter fluid to make them light all at the same time lol