Spyder Forums  

Go Back   Spyder Forums > Spyder Markers > Discontinued Markers
FAQ Members List Calendar Search Today's Posts Mark Forums Read

Reply
 
Thread Tools Display Modes
  #1  
Old 11-11-2007, 08:40 AM
DonF's Avatar
DonF DonF is offline
Member
 
Join Date: Jul 2007
Location: Oregon
Posts: 97
Default VS O-Ring Info Project

Since the last VS O-ring threads got side tracked for profit. I have decided to start a new thread I will match up O-rings as time allows and edit this first post. It doesnt cost anything to match up O-rings except, Time - an O-ring Chart, and a set of Calipers So if you want to join in the project please feel free to do so. I will call Kingman Tech to see if they are allowed to give out this info too.

----------------------------------------------------------------------------------------------------------------------------
O-rings are listed by the numbers in the Kingman VS Manual

ORG001 - Striker O-ring Size = #015 Material = Polyurethane (Urethane) Duro = 70 Note: Page 13 of the VS manual warns against using a tank O-ring its polyurethane too but its a 90 Duro (too hard) or the substitution of ORG002 Black O-ring - In a jam the ORG002 might work but not last as long, as polyurethane has much better tearing / wear capabilities. One each used in the VS marker

ORG002 - Bolt O-ring (Also used on the Vertical Adapter x2 and the outside of the Valve Body x2 Low Pressure Chamber x1) Size = #015 Material = Standard Nitrile is also known as Buna-N or Buna. Duro = 80 (per VS manual) Note: most O-ring suppliers only stock 70 or 75 Duro in Nitrile This will work fine. Six are used in the VS Marker

ORG003 - Barrel O-ring Size = #019 Material Buna-N / Nitrile One / Two each used in the VS marker depending on your barrel (stock VS uses two)

ORG005 - Vertical O-ring Size = #018 Material Buna-N / Nitrile One each used in the VS marker

ORG006 - Inner Valve Body O-ring Size = #008 Material Buna-N / Nitrile One each used in the VS marker

ORG008 - Velocity Adjuster O-ring Size = #011 Material Buna-N / Nitrile This size is also used on the Macroline adapter on the stock regulator. TheVS manual calls for a #10 but that is way too small. The O.D. of the velocity adjuster is.325 and the O.D. of the macroline adapter is.335. The I.D. of a #010 oring is .239 +/-.005 The #011 ID is .301 +/-.005 still tight but ok. #012 is way too big at.364 - One / Two is used on the VS depending on if you run the stock regulator

ORG009 - ASA Reg Head O-ring Size = #016 Material Buna-N / Nitrile One each on the VS

ORG010

ORG011

ORG012

ORG013

ORG016 - Valve Pin O-ring (L) Size = #009 Material Buna-N / Nitrile One each used in the VS marker

ORG017 - Valve Pin O-ring (S) Size = M1x3 (Metric O-ring its 1mm cross section by 3mm I.D. Some places like oringsusa list the it backwards as a 3x1 so be careful) Material Buna-N / Nitrile One each used in the VS marker

Tank O-ring Size = #015 Material = Polyurethane (Urethane) Duro = 90

Links
http://www.marcorubber.com/sizingchart.htm O-ring Sizing Chart


http://www.marcorubber.com/material_chart.htm O-ring Material Chart


http://www.customproducts.us/downloads.html Maintenance Guides and O-ring sizes for Custom products ASA's and Regulators The CP regulator guide also works for the Empire regulator with a few minor changes.


http://www.spyder.tv/section/support/diagrams_manuals.html Spyder VS marker manuals (The O-rings above are listed by the Kingman Part Number)


Where to Find O-rings

Phone = KINGMAN - After all they made your marker the tech guys are Cool - Very Helpful and your sure to get something that works

Locally = Hardware Stores, Building Supply Stores, Industrial Supply Stores, Harbor Freight, Tool Stores and your local PB shack probably has a large selection
Online = Most any O-ring supply store or paintball outlet

When matching up old O-rings to a O-ring chart you need a set of calipers. Digital Calipers can be found at stores like Harbor Freight for under $7 on sale. O rings are not that precision even the quality ones list a +/-.003 Variance, So an expensive set of calipers is not needed.
Used O-rings deform so don't expect exact results. Measure the cross section of the O-ring then measure the diameter of the item the O-ring fits on. Much more accurate than trying to measure the ID of a flexy O-ring

Poor Quality orings can vary up to .007-.010 because of mold quality. So if you find a bad batch find another supplier and return them
__________________

Last edited by DonF : 11-11-2007 at 08:52 PM.
Reply With Quote
  #2  
Old 11-11-2007, 09:32 AM
Critical's Avatar
Critical Critical is offline
I didn't do it...No witnesses survived
 
Join Date: Jan 2006
Location: People's Republic of Maryland
Posts: 1,554
Default Re: VS O-Ring Info Project

__________________
SOC Feedback: +32/-0

"To sit back hoping that someday, someway, someone will make things right is to
go on feeding the crocodile, hoping he will eat you last - but eat you he will"
Ronald Reagan
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -8. The time now is 04:08 AM.