Spyder Forums  

Go Back   Spyder Forums > General Spyder Discussion > Veteran Forum
FAQ Members List Calendar Search Today's Posts Mark Forums Read

Reply
 
Thread Tools Display Modes
  #11  
Old 04-12-2006, 07:31 PM
ricochet08's Avatar
ricochet08 ricochet08 is offline
Spyder Addict
 
Join Date: Dec 2005
Posts: 817
Default Re: just got my NDZ valve and........

o yea forgot to ask about this:

which hole should i screw the bronze colored screw into, the big/wide one? or the small one?
or does it make a difference?
on the stock valve, both the top and bottom of the valve have holes. not where the valve pin goes, but where the screw goes. but im sure y'all knew that
__________________
*****May 2006 Spyder of the month winner!!!*****

feedback: http://www.spyder.tv/forums/showthread.php?t=819
Reply With Quote
  #12  
Old 04-12-2006, 07:37 PM
DRAGON's Avatar
DRAGON DRAGON is offline
sna'foo.....um.....gesund heit
 
Join Date: Dec 2005
Location: Land of the Sun
Posts: 3,658
Default Re: just got my NDZ valve and........

Umma.......there's only 1 way it can go on since 1 hole is completely blocked off lolzerz **HINT** "Look for the obvious"
__________________
KUSA Old School Alumni #4939
Registered: 6/26/02
Posts: 14,000+ before the old mothership went down

Jealousy is the tribute mediocrity pays to genius while feeling alone apposed to smiling adversaries....

http://www.spyder.tv/forums/image.php?type=sigpic&userid=6&dateline=1201845216
Reply With Quote
  #13  
Old 04-12-2006, 08:24 PM
ricochet08's Avatar
ricochet08 ricochet08 is offline
Spyder Addict
 
Join Date: Dec 2005
Posts: 817
Default Re: just got my NDZ valve and........

but i didn't know which hole should've been used to keep the valve in place

but i got it now the leak is no longer among me

now to only stop the machine gunning

and to answer ur questino dragon, i was running @ 200psi before i put the NDZ valve in. also, stock valve spring.
tried upping the pressure to make it stop. made it worse
__________________
*****May 2006 Spyder of the month winner!!!*****

feedback: http://www.spyder.tv/forums/showthread.php?t=819
Reply With Quote
  #14  
Old 04-12-2006, 08:30 PM
DRAGON's Avatar
DRAGON DRAGON is offline
sna'foo.....um.....gesund heit
 
Join Date: Dec 2005
Location: Land of the Sun
Posts: 3,658
Default Re: just got my NDZ valve and........

200psi at what velocity? That's way to low a pressure for a Spyder. Spyder's are meant for 300-400psi for best all around LP results. It's leaking at 200psi because that's too low a pressure to keep the valve closed properly. 200psi.......shame on you! -
__________________
KUSA Old School Alumni #4939
Registered: 6/26/02
Posts: 14,000+ before the old mothership went down

Jealousy is the tribute mediocrity pays to genius while feeling alone apposed to smiling adversaries....

http://www.spyder.tv/forums/image.php?type=sigpic&userid=6&dateline=1201845216
Reply With Quote
  #15  
Old 04-13-2006, 09:05 AM
Nader's Avatar
Nader Nader is offline
Do what you like.
 
Join Date: Dec 2005
Location: Whore Island, CO
Posts: 1,227
Default Re: just got my NDZ valve and........

Is it "machine gunning" with the regular valve too? It could be your sear, it may be worn down. Try sharpening it. And yes, 200psi is way too low, and not efficient at all either...
__________________
Stay on the other side of the road
'Cause you can never tell
We've a thirst like a gang of devils
We're the boys of the county hell
Reply With Quote
  #16  
Old 04-13-2006, 02:10 PM
ricochet08's Avatar
ricochet08 ricochet08 is offline
Spyder Addict
 
Join Date: Dec 2005
Posts: 817
Default Re: just got my NDZ valve and........

hmmm....well, im not sure of the velocity, as i don't have a chronograph on hand but it's pretty low.

i turned the pressure up to 500psi, and it still did the same.

nader: wasnt machine gunning with the regular valve. i'll check the sear asap.
__________________
*****May 2006 Spyder of the month winner!!!*****

feedback: http://www.spyder.tv/forums/showthread.php?t=819
Reply With Quote
  #17  
Old 04-13-2006, 02:17 PM
DRAGON's Avatar
DRAGON DRAGON is offline
sna'foo.....um.....gesund heit
 
Join Date: Dec 2005
Location: Land of the Sun
Posts: 3,658
Default Re: just got my NDZ valve and........

Sometimes the Rocket valves have the same exact sealing probs. For those you can just take the seal and push it into the valve body while turning it. This seats or conforms the seal into the body -
__________________
KUSA Old School Alumni #4939
Registered: 6/26/02
Posts: 14,000+ before the old mothership went down

Jealousy is the tribute mediocrity pays to genius while feeling alone apposed to smiling adversaries....

http://www.spyder.tv/forums/image.php?type=sigpic&userid=6&dateline=1201845216
Reply With Quote
  #18  
Old 04-14-2006, 04:34 PM
ricochet08's Avatar
ricochet08 ricochet08 is offline
Spyder Addict
 
Join Date: Dec 2005
Posts: 817
Default Re: just got my NDZ valve and........

so wat ur saying dragon is, it makes a bit of a groove to provide for a better seal?

btw, i polished my sear up a bit, and the machine gunning stopped
__________________
*****May 2006 Spyder of the month winner!!!*****

feedback: http://www.spyder.tv/forums/showthread.php?t=819
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -8. The time now is 05:42 PM.