|
|
#11
03-12-2008, 04:48 AM
|
||||
|
||||
Re: FPS fluctuations with HPA ??
As far as a regulator goes...I dont want to get one that fits to the MR directly as I want to be able to use my air for my TIPPy as well. So I want to be able to put it directly on the tank. Do they make one like that ?
What should I look for -type ? ratings ? etc. 
|
|
#12
03-12-2008, 05:44 AM
|
||||
|
||||
|
Re: FPS fluctuations with HPA ??
the more I read about this the more it makes me wary. It seems there is a lot more to it than just adding a regulator and high flow valve. It appears I also need Valve springs changed and "change the lines too ??".....<sigh> I am a little frustrated mainly becuase of a lack of knowledge about this....
|
|
#13
03-14-2008, 09:50 AM
|
|||
|
|||
|
Re: FPS fluctuations with HPA ??
If you are running a remote you can just screw a torpedo into your asa, you could also do this for your tippy. You can also get a palmers to go right off your tank (little pricey). If you are thinking of going lp you need to read otters pages first. Sundragon also has a good right up on going lp with a MR spyder. It would seem that the madmann rocket valve is the best choice for the MRs because of the built in valve spring. To the best of my knowledge there are not after market valve springs for the MRs available. I am getting ready to go lp on my mr2 using a drilled out stock valve and a torpedo I already have. If I can't get it tuned with that valve I am going with the rocket. I can let you know how it goes.
*just reread your post didn't see you were using hpa, you could put any good male threaded reg in your asa and use a remote. What kind of tank are you using? What knid of reg is on it?
__________________
Guns don't kill people. Chuck Norris kills people. Last edited by Lonus : 03-14-2008 at 10:02 AM.
|
|
#14
03-14-2008, 11:05 AM
|
||||
|
||||
|
Re: FPS fluctuations with HPA ??
I have a Pure Energy 68/4500 HPA tank. I have a Palmer inline stab, that goes on the remote by the tank like you mentioned, on the way. I jsut have the stock valve in there. Think I'll need the high flow valve for sure ? I DONT want to go LPA ....too much work....
|
|
#15
03-16-2008, 07:14 PM
|
|||
|
|||
|
Re: FPS fluctuations with HPA ??
With the stock valve you might get the pressure down to 600 psi. If you want to go lower I think you will need a new valve.
__________________
Guns don't kill people. Chuck Norris kills people.
|
|
#16
03-17-2008, 04:51 AM
|
||||
|
||||
|
Re: FPS fluctuations with HPA ??
got it...
|
|
#17
08-10-2009, 02:55 PM
|
||||
|
||||
|
Re: FPS fluctuations with HPA ??
should one go with just the 32* valve or get the whole kit for the few extra dollars.
this is for a gen 1 mr2 with cp reg and hpa thanks
|
|
#18
08-10-2009, 04:05 PM
|
||||
|
||||
|
Re: FPS fluctuations with HPA ??
Probably best to make your own thread.. this one is a year old.
__________________
-BATTLEchaser Feedback - MCB / SOC / PBn / IOG / CC / eBay Quote:
|
 |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
