Forum: Discontinued Markers
09-28-2008, 08:06 AM
|
|
Replies: 21
Views: 1,506
Re: Thinking about getting this marker...
Afraid you're going to have todo some research. Goto a site like PBreviews. c o m and go thru the different varieties of electronic markers. More the low-end ones, but if you buy used you can...
|
|
Forum: Discontinued Markers
08-28-2008, 03:55 PM
|
|
Replies: 6
Views: 679
Re: Asa
I fixed it; ended up fitting a washer under the snap-ring. Now, when my ASA stops moving in the 'off' direction, the pin is completely retracted.
|
|
Forum: Discontinued Markers
08-07-2008, 07:35 AM
|
|
Replies: 11
Views: 1,702
Re: high pressure or low pressure?
Tank output should be HP (700psi+), the VS2's asa/regulator should reduce that pressure to LP(around 200psi).
The regulator on a VS2 is made to receive HP and flow may be diminished if pressure is...
|
|
Forum: Electronic Markers
08-02-2008, 07:26 AM
|
|
Replies: 13
Views: 1,535
Re: New 2008 Electra w/ Ey Size Comparison
heh...
A Regulator controls the air pressure that enters your gun.
The ASA(Air Source Adapter) is where you screw on your air tank. Sometimes these have a on/off valve.
They should be connected by...
|
|
Forum: Electronic Markers
07-31-2008, 06:22 AM
|
|
Replies: 9
Views: 1,385
|
|
Forum: Discontinued Markers
07-14-2008, 12:42 PM
|
|
Replies: 6
Views: 679
Re: Asa
If I keep twisting my on/off past the off position the pin actually stops retracting and starts extending again. When I reach my maximum off position, the pin is 20% entended. I always assumed it...
|
|
Forum: Discontinued Markers
07-10-2008, 09:22 AM
|
|
Replies: 6
Views: 679
Re: Asa
Be aware that the VS2 will bleed air in the maximum off position.
Try putting your tank on with your marker with the ASA a 1/2 turn away from the off position.
|
|
Forum: Discontinued Markers
07-08-2008, 06:28 AM
|
|
Replies: 7
Views: 627
Re: Have any Vs2 owners tried the new Electra yet
My buddy had two minor issues,
-At one point the LED started flashing yellow(possibly due to battery wire being loose).
-Once, the gun didn't recock completely(reg not broken-in enough, pressure set...
|
|
Forum: Discontinued Markers
07-04-2008, 07:35 AM
|
|
Replies: 7
Views: 627
|
|
Forum: Discontinued Markers
06-30-2008, 07:12 PM
|
|
Replies: 3
Views: 593
Re: vs2 magnet mod --- how do i do it?
He means if the magnets reach eachother before your trigger contacts the micro-switch, there will be no trigger squeeze left to depress the microswitch.
Your magnets would 'bottom-out' your trigger...
|
|
Forum: Electronic Markers
06-12-2008, 06:56 AM
|
|
Replies: 13
Views: 1,535
|
|
Forum: Discontinued Markers
06-07-2008, 09:02 AM
|
|
Replies: 10
Views: 729
Re: eyes
Your board eyes may be set to bouncebeam?
Anyway to adjust eye sensitivity?
|
|
Forum: Discontinued Markers
06-07-2008, 08:53 AM
|
|
Replies: 1
Views: 887
Re: Regulator?
I used a strap wrench. Ensure that your marker is completely depressurised.
The macroline elbow-joint should rotate freely, allowing you to remove your foregrip without unplugging your macroline....
|
|
Forum: Electronic Markers
06-06-2008, 10:47 AM
|
|
Replies: 11
Views: 569
Re: i need big help
oh boy... where to begin...
-Could be the ACS bolt preventing you from chopping your slow feeding balls.
-Could be your velocity screw is adjusted too far forward, preventing the bolt from reaching...
|
|
Forum: Non-Paintball Topics
06-02-2008, 02:39 PM
|
|
Replies: 30
Views: 1,193
|
|
Forum: News & Updates
06-02-2008, 11:09 AM
|
|
Replies: 1
Views: 813
|
|
Forum: General Spyder Forum
04-05-2008, 05:31 AM
|
|
Replies: 9
Views: 610
Re: force feed hopper
What kind of gun are you using? Check your eyes... if you have any... if not, that's your problem.
If it's a pilot, then your ACS bolt can only do so much.
|
|
Forum: General Spyder Forum
04-03-2008, 08:36 AM
|
|
Replies: 4
Views: 607
|
|
Forum: General Spyder Forum
04-03-2008, 08:32 AM
|
|
Replies: 4
Views: 607
Spyder RS and RSX
http://www.spyder.tv/section/products/rs_series/index.html
Maybe I missed something, but are these old? (forgive my ignorance if they are)
|
|
Forum: Discontinued Markers
04-02-2008, 05:33 AM
|
|
Replies: 6
Views: 578
Re: Foregrip rubber, unwanted movement
I haven't even tried removing it yet, but judging by how easily it turns, I'd figure it would be possible. It's probably easier if you take it off first(the foregrip).
|
|
Forum: Discontinued Markers
04-01-2008, 08:49 AM
|
|
Replies: 6
Views: 578
|
|
Forum: Discontinued Markers
03-31-2008, 02:48 PM
|
|
Replies: 6
Views: 578
Foregrip rubber, unwanted movement
I know most people just replace the foregrip with a regulator but I haven't yet and am stuck with the stock for now.
As we all know, the stock foregrip is just a hollow tube with a rubber grip around...
|
|
Forum: Discontinued Markers
09-29-2007, 09:18 AM
|
|
Replies: 7
Views: 554
Re: CP Asa
I'm curious as well.
From what I can tell, Dovetail is the one that fits properly, but Directmount will fit, just not as well. As far as I know, the VS2 has a dovetail ASA mount.
Can anyone clarify?
|
|
Forum: Discontinued Markers
09-20-2007, 08:37 PM
|
|
Replies: 9
Views: 653
Re: Sweet deal!
The foregrip on a VS2 is NOT a regulator, it's merely an expansion chamber. You would need to replace it with a regulator if you exchanged your stock reg/on-off for a aftermarket asa on-off.
|
|
Forum: Discontinued Markers
09-05-2007, 08:58 PM
|
|
Replies: 18
Views: 931
|
