Spyder Forums

Spyder Forums (http://www.spyder.tv/forums/index.php)
-   Electronic Markers (http://www.spyder.tv/forums/forumdisplay.php?f=92)
-   -   Electra bolt will not lock back (http://www.spyder.tv/forums/showthread.php?t=200)

Woofer 12-29-2005 07:39 AM

Electra bolt will not lock back
 
I just bouight my son a new spyder electra ACS for christmas. It worked fine on christmas day, but a few days later the bolt would not lock back to the rear. The battery has a full charge and the tank is full. Has anyone else had this problem? If so what can I do to fix it.
Thank you.:confused: :(

ooglieboogliebob 12-29-2005 11:49 AM

Re: Electra bolt will not lock back
 
well .. all i can think of right now .. is that the trigger's not on correctly ... or you dissassembled your gun .. that day and didn't put it in right ...

I'v heard some problems like this before .. and it was from assembling it funny.. once i hard the striker buffer was in front of the striker rather than behind it ...

It also could be that on your trigger ... the sear's not keeping the striker in place.. but i wouldn't know why it would do that ...

Just post back and .. tell me what you did with the gun ... it'd make it a little bit easier :p

ad0131065 12-29-2005 11:58 AM

Re: Electra bolt will not lock back
 
is the trigger frame tightend to the gun well? you could have lost the sear spring also. I dont see how the striker buffer would cause it to not catch.....but yes, more info please and welcome to the forums.

ooglieboogliebob 12-29-2005 12:11 PM

Re: Electra bolt will not lock back
 
well .. it wouldn't let it cock .. cuz it was like this ..
striker buffer > striker > spring > striker spring guide > Flat disk > Plug

Rather than ...
striker > striker buffer > spring > striker spring guide > Flat disk > Plug

And this caused the striker to move back farther ... not allowing the sear to catch on the striker ...

DexGtr 12-29-2005 12:13 PM

Re: Electra bolt will not lock back
 
Quote:

Originally Posted by ad0131065
I dont see how the striker buffer would cause it to not catch.....but yes, more info please and welcome to the forums.

if the bumper is in front he won't be able to completely open up the valve and in turn you have less gas to push your striker back.

audi 12-29-2005 01:21 PM

Re: Electra bolt will not lock back
 
if that stuff dosent work ( it should ) try streching out your spring this shouldnt be the problem because its new.

ooglieboogliebob 12-29-2005 02:29 PM

Re: Electra bolt will not lock back
 
.... well if even all of that doesn't work .. just email kingman .. they should be able to fix it for you for ..probably free since it's new .. unless you did something to damage it .. but kingman proably wouldn't care :p ... The should be able to help you most likely .. if they can't they'd probably just send you a new gun

thechubbss12 12-30-2005 07:12 AM

Re: Electra bolt will not lock back
 
Humm this should be a simple problem but i dunno sometimes weird things happend to spyders...
Ok ima gunna give you a list of things to do if you follow them right it should get your sons spyder back in working order.
1. Take all internals out of you gun (striker, bolt, etc)
2. Unscrew the ASA (place were your tank goes), well take the screws off
3. now take off the trigger frame (only two screws but be sure not to loose the wasers because in some cases if you do lose the washers you will have problems with the striker attacking the screws when they are fastened into the gun tightly)
4. Now that everything is out you should have all of this stuff lying outside of your marker. (Bolt, Striker, Striker buffer, Spring, Spring Guide, Velocity Adjuster, pin for Velocity Adjuster, small Disks that go inside Velocity Adjuster, trigger frame, screws for frame and ASA)
5. Now put the bolt and striker back together and put them into the marker (make sure that the front end of the striker (the part with the o-ring) is facing foward toward the valve assembily)
6. If you want u can put the striker buff back into the marker. Althoguh it realy isnt an important part to the gun, but you can put it in if you feel like it.
7. Now put the disk into the Velocity Adjust
8. Put the spring into the striker(already inside the marker), then put the spring guide into the spring.
9. Put the Velocity adjuster in the marker and secure it with the Velocity Adjuster pin
10. Lastly put the trigger frame on and besure you did not loose any of the washers lol. then put you ASA back on.

Now your free to air it up is should fire and recock fine... if not you can E-mail me at thechubbss12@yahoo.com or AIM me at thechubbss12


All times are GMT -8. The time now is 08:18 PM.