View Full Version : clamp feeds for vs2

03-11-2007, 04:40 PM
wat are some clamp feeds that fit the vs?

03-11-2007, 04:47 PM
anything impulse threaded.

The trinity ones are nice.

03-11-2007, 05:24 PM
u got a site? :P

03-11-2007, 05:26 PM
www.actionvillage.com ;)

http://www.actionvillage.com/is-bin/INTERSHOP.enfinity/eCS/Store/en/-/USD/DisplayProductInformation-Start;sid=RCaDZiFvQbuD_2Sb2hRDzivJzDIrrqDeR_M=?Pro ductID=jBHAqArbQFwAAAEQyrqXIFCr
thats a NDZ feedneck.

03-12-2007, 04:48 PM
Anyone know if thats a good feed? anyone know from experience or anything?

03-12-2007, 05:05 PM
wat are some clamp feeds that fit the vs?
am I allowed to cry in a corner

but yeah ndz stuff is awesome my brother has that feed and I used it on my vs2 but why do you need that

03-13-2007, 04:33 AM
anything impulse threaded.

redz makes a nice one that is impulse threaded-


03-13-2007, 06:21 PM
the twist feed is a pain in the ass with my hopper..i gotta really grind it down into the hopper to make sure it dont wobble. jus think a clamp feed wuld be easier

03-13-2007, 06:33 PM
Lighjtly sand the neck of the hopper with 80 grit sandpaper(clean it after). It will grip much better afterwards. Scuff it up, that's it. I have a Fasta and have no prob at all with the stock VS feedneck. Was your Egg neck sanded down to fit another marker perhaps? -

I use CCM necks on my other markers -

03-14-2007, 01:51 PM
nope brand new ill try sanding

03-15-2007, 05:57 AM
I have heard the Redz one from above is great. Also, on action village go to their closeout store and there are a few for dirt cheap.

03-17-2007, 06:35 AM
anything impulse threaded.

The trinity ones are nice.
is that the same for vs3

03-17-2007, 11:44 AM

I have an NDZ on my electra and a Trinity on my VS3. Both are pretty good quality, and I have no complaints about them.

04-12-2007, 02:16 PM
i got a clamp feedneck for my vs3 today screwe it in and went to put on my diablo tsa frontman but it wouldent clamp and its as far as in it will go. how do i fix it....

04-17-2007, 09:52 PM
Which feedneck has the lowest profile? I have a ReLoader B and with the stock feed neck it sits very high (as well as being murder to twist lock, I use a strap wrench) so I'm looking for a really low profile neck. I've heard about the CCM neck but dont know which one is smaller: No-rise or No-pro...

Does anyone know/suggest any other clamping feedneck thats low profile?

04-17-2007, 10:23 PM
Ejamiec, do you mean it's all the way clamped down and the sucker still wouldn't tighten? Use a strap wrench to tighten it, or use some rubber bands around the feedneck of the hopper to enlargen it.

Krytos, No-rise is shorter than the No-pro. I believe CCM has a size chart somewhere on their website. The Q-Lock is an excellent alternative, and is cam-locking (my favorite flavor of feedneck). With a cam-lock, you can tighten it down as far as it will be reasonable, and then some, all without tools. To get the hopper on, open the lever on the feedneck, plop the hopper in, and then close the lever. With these, you have to make certain you do not over tighten, or else you'll be buying a new feedneck assembly for your ReloaderB. ;)