bigred76
01-06-2007, 08:52 AM
Welp, I realized I haven't let most of you guys into my recent stream of markers. No, I'm not gonna tell you what it is yet. That'll come in a little bit after I start talking. If you don't care for my blather, scroll down to the pix already! I ended up trading my Promaster for a Mag (known as Amanda, now... ;), and traded that for an Ion, then sold the Ion and Mag to get my newest marker... Some of you have been in on this throughout, via the chatroom (being in the 'circle' pays, sometimes!).
After being markerless for a little bit, I finally had enough moolah to get an older high-end gun for a nice price. Originally I was gonna get an Alias, but that deal fell through. I decided to go with my fall-back, this Shocker. Yes, you might have seen it before (10 brownie points and an e-cookie to the first person who knows who I got it from that WAS NOT told by me or the original owner, AND can link to it! If you know the orignal poster, the second part shouldn't be too hard. Yes, 'twas on these boards... Only one like it I've seen pass through here so far! :)). It has a broken on/off switch, and I accidently brokethe female connector off the lower board, too, so I have to replace those parts before I even can turn it on. But, on the flipside, I've almost got the trigger right where I like it, so when it does get turned on, I know it'll rip! :D
I also have picked up a new carbon fiber tank recently, a 68/45 Apocalypse 2k. Great, long rail on it so I can make it as short as a 45/45 (almost), or as long as a reverse dropped 68/45. I <3 it! Gonna run it somewhere between 400 and 550 psi just because I can. Pictures are taken with my new camera I got for Christmas, a HP Phtosmart E327. Not the best camera by any means, but it blows Druid's webcam outa the water. :D Part of the bad quality was just me wanting to get some quick shots to post them up. I'll try for better ones later.
Without much more of my blathering, here are the specs of my new gat:
04 Shocker Red (almost pink, hoping it will finish fading soon!) to Pewter fade
Virtue board
Stock bolt with NDZ firing can (have to get some o-rings for the side-seals before it's installed... it's red, btw)
Dye Stickies
CP Shorty Reg
Freak Kit
Shocktech feedneck
CP rail
NDZ ASA w/ gauge
NDZ roller bearing trigger
http://i4.photobucket.com/albums/y109/bigred76/Shockah/HPIM0049.jpg
http://i4.photobucket.com/albums/y109/bigred76/Shockah/HPIM0052.jpg
http://i4.photobucket.com/albums/y109/bigred76/Shockah/HPIM0053.jpg
http://i4.photobucket.com/albums/y109/bigred76/Shockah/HPIM0050.jpg
http://i4.photobucket.com/albums/y109/bigred76/Shockah/HPIM0051-1.jpg
So, what do you guys think? :)
After being markerless for a little bit, I finally had enough moolah to get an older high-end gun for a nice price. Originally I was gonna get an Alias, but that deal fell through. I decided to go with my fall-back, this Shocker. Yes, you might have seen it before (10 brownie points and an e-cookie to the first person who knows who I got it from that WAS NOT told by me or the original owner, AND can link to it! If you know the orignal poster, the second part shouldn't be too hard. Yes, 'twas on these boards... Only one like it I've seen pass through here so far! :)). It has a broken on/off switch, and I accidently brokethe female connector off the lower board, too, so I have to replace those parts before I even can turn it on. But, on the flipside, I've almost got the trigger right where I like it, so when it does get turned on, I know it'll rip! :D
I also have picked up a new carbon fiber tank recently, a 68/45 Apocalypse 2k. Great, long rail on it so I can make it as short as a 45/45 (almost), or as long as a reverse dropped 68/45. I <3 it! Gonna run it somewhere between 400 and 550 psi just because I can. Pictures are taken with my new camera I got for Christmas, a HP Phtosmart E327. Not the best camera by any means, but it blows Druid's webcam outa the water. :D Part of the bad quality was just me wanting to get some quick shots to post them up. I'll try for better ones later.
Without much more of my blathering, here are the specs of my new gat:
04 Shocker Red (almost pink, hoping it will finish fading soon!) to Pewter fade
Virtue board
Stock bolt with NDZ firing can (have to get some o-rings for the side-seals before it's installed... it's red, btw)
Dye Stickies
CP Shorty Reg
Freak Kit
Shocktech feedneck
CP rail
NDZ ASA w/ gauge
NDZ roller bearing trigger
http://i4.photobucket.com/albums/y109/bigred76/Shockah/HPIM0049.jpg
http://i4.photobucket.com/albums/y109/bigred76/Shockah/HPIM0052.jpg
http://i4.photobucket.com/albums/y109/bigred76/Shockah/HPIM0053.jpg
http://i4.photobucket.com/albums/y109/bigred76/Shockah/HPIM0050.jpg
http://i4.photobucket.com/albums/y109/bigred76/Shockah/HPIM0051-1.jpg
So, what do you guys think? :)