PDA

View Full Version : sanding down vlocity.


johnnyblast
06-06-2006, 10:40 AM
i want to sand down vlocity's tube because its little bit too high... what kind of sander should i use? i dont think i can cut it off because the tube might crack... let me know guys. thanks!

bamf-hacker
06-06-2006, 10:49 AM
Use a dremel with a cut off wheel... It should not crack. Just be careful.

HacKeR

druid
06-06-2006, 01:02 PM
or a hack saw. Mount the loader into the feedneck and use a sharpie to draw around th4e neck so you have a nice, clean line to cut on.

ShadowX
06-06-2006, 01:55 PM
Yea, I have cut a couple feed necks on different hoppers and I say use a hacksaw and the method that druid explained..

ooglieboogliebob
06-06-2006, 03:34 PM
yep .. hacksaw method will work .. but i'd probably use a file after to smoothen out rough edges ... i hate em .. :p

SparkyGT
06-08-2006, 01:33 PM
on my egg, i used a hoseclamp on where i wanted the cut and then went nuts with the grinder, clamp is good for a guide, quick touch up with a file on the edges after. total time about 1 minute

thechubbss12
06-08-2006, 05:58 PM
Propane Torch and a Steel rod about .5cm in diameter.....

Draw a line.... Light torch... Put on heat resistant gloves... Heat rod until it turns red then quickly Place on the line and watch the magic.... File off any bulges in the plastic....

Perfectly clean heat cut...

Or you could use a sander with 150 Grit sandpaper and sand away.

johnnyblast
06-10-2006, 03:40 PM
i used a small hand saw which i found it in my garage and it sure did its job but its not a stright line... now i need to sand sand sand away~~ anyways, is it possible to get new fewneck tube from viewloader for my vlocity?? just incase i cut my tube too short.

thechubbss12
06-10-2006, 06:55 PM
Yea just email them.... they have OK customer service.

claustrophobia9
06-16-2006, 08:30 AM
for the vlocity?.... uh i dont think itll be possible for awhile especailly if its a 3 piece design like the halo's

johnnyblast
06-16-2006, 09:54 AM
thanks guys!! everything worked out great. my vlocity was kinda high for my pm5 with ccm no-pro feedneck and now its perfect!!!

claustrophobia9
06-16-2006, 11:09 AM
thanks guys!! everything worked out great. my vlocity was kinda high for my pm5 with ccm no-pro feedneck and now its perfect!!!
we want pics

johnnyblast
06-16-2006, 11:20 AM
as soon as i get home i'll take a picture and load it up to putfile, come back tomorrow for picture!!

johnnyblast
06-20-2006, 10:42 AM
i took the picture late at night so its pretty dark but you get the idea. my vlocity was ABOUT half an inch taller. my pm5 with basic upgrades: cp trigger, hybrid grip and ul barrel. enjoy!

http://f5.putfile.com/6/17020081447.jpg

http://f5.putfile.com/6/17020073583.jpg

Nenkitsune
08-08-2006, 08:01 PM
i just stuck my hopper into the feedneck, clamped it down where i want it, and hacked it to size. worked pretty damn good. took all but 1 minute hah.

Ace24
09-08-2006, 03:53 PM
I stuck the hopper neck in my feedneck on the gun first, drew around it with a marker at the point where I wanted it to be cut, and then took it and cut it with a jiggsaw. (That was the easiest way I could think of, untill I relised my rotozip still works)

Then I took it to my belt sander and sanded it rounded and smooth. Now it looks professionally done! Its quite easy.

Oh I didnt do this with a Vlocity though. I did it with an Evlution Viewloader II.