PDA

View Full Version : wtb vs2/3 or rs/x internals and trinity block


DRTHV8R
03-21-2009, 09:23 PM
hey guys i've been working on a custom project for awhile now and my valve went to heck on me. i have a short wtb list for internals for the gun. i'm looking for vs/rs internals as they should operate on a much lower pressure

vs2/3 or rs/x series valve assembly (with poppit, cupseal, spring, all that jazz)
vs2/3 or rs/x series hammer/ram
^^ springs or spring kit
trinity front block, vs series or normal spyder series, black would be preferable

thanks ahead of time everyone!

fernando8877
03-22-2009, 11:50 AM
i got some vs1 parts, including a valve. lmk if interested.........

ferret15
03-22-2009, 12:17 PM
he is looking for a the LP internals.

~balance valve http://www.sundragonpps.com/catalog/item/3373182/5657395.htm
~mini striker http://www.sundragonpps.com/catalog/item/3373147/5433125.htm
~vs main spring http://www.sundragonpps.com/catalog/item/3373147/4884414.htm

the main spring is shorter than the standard spyder size,

the valve spring is the newer blackish blue color and is lighter. I reccomend a spring kit and just use a spring from there
http://www.sundragonpps.com/catalog/item/4498366/4991793.htm

Paintball Freak
03-22-2009, 03:21 PM
I may be getting rid of those internals soon, I'll keep you posted. = )

DRTHV8R
03-22-2009, 07:24 PM
i got some vs1 parts, including a valve. lmk if interested.........

kinda looking for low pressure parts but i'll keep you in mind

he is looking for a the LP internals.

~balance valve http://www.sundragonpps.com/catalog/item/3373182/5657395.htm
~mini striker http://www.sundragonpps.com/catalog/item/3373147/5433125.htm
~vs main spring http://www.sundragonpps.com/catalog/item/3373147/4884414.htm

the main spring is shorter than the standard spyder size,

the valve spring is the newer blackish blue color and is lighter. I reccomend a spring kit and just use a spring from there
http://www.sundragonpps.com/catalog/item/4498366/4991793.htm

thumbs up to you and thanks

I may be getting rid of those internals soon, I'll keep you posted. = )

that would be great thanks

how does the madman valve stack up against the vs lp valve? i'll explain a little bit what i'm doing. i've so far taken an xtra and a psychoballistics silver bullet. i half-blocked the silver bullet body and chromed it. added and cut a shocktech feedneck (matching) and drilled out the xtra front block (its a bit bigger than the silver bullet) and used the silver bullet lpc since it is a bit larger inside than the xtra, also chromed it. i added a pure energy reg and a rocking trigger with the rocking trigger ram/hammer. installed a shocktech bolt, made spacers for the grip frame screws, installed a redz grenade asa, and made a custom adapter plate. also, i was using the psychoballistics cupseal/valvestem because it was only one piece and it was a bit lighter. lastly, i swapped out sear springs becaus the stock one from the rocking trigger was too stiff.

the gun was actually running for awhile, and then i went to show it to some friends and it started leaking, probably cause i had the regulator up almost full from when i put everything together to make sure it worked. i couldn't put my finger on where the leak was coming from so i replaced every oring in the marker. i also found a leak in the regulator so i didn't put it back on and just screwed the tank right into the front block. i had about 2500 psi at a 850 psi output and no luck at all. the bolt wouldn't recock. i tried swapping out poppit and velocity springs with no luck. tried dropping the frame a bit just incase the sear was sitting too high also without luck.

my idea was to just swap out the guts of the marker with low pressure internals. i looked at that website link and there are some good ideas.

but any suggestions on what to do with the marker to get it running again and on a low pressure would be great.

so how does the madman stand up the the vs lp valve? the dragonfly striker compared to the vs replacement striker? vs spring kit or regular spyder spring kit? i kinda morphed this thread into something that should go somewhere else but if anyone has these parts or input, it would be much appreciated!

also, if anyone simply has a vs2/3 that they are selling for cheap, i wouldn't mind taking it off their hands as long as it works

thanks again