PDA

View Full Version : XSiv Launcher


XSiv Force
07-30-2008, 09:53 AM
Here is "Big Boy"
http://i304.photobucket.com/albums/nn200/XSiv_Force/DSCN0131.jpg
http://i304.photobucket.com/albums/nn200/XSiv_Force/DSCN0132.jpg
http://i304.photobucket.com/albums/nn200/XSiv_Force/DSCN0133.jpg
http://i304.photobucket.com/albums/nn200/XSiv_Force/DSCN0134.jpg

XSiv Force
07-30-2008, 09:55 AM
if you guys want i can post how to make one similar to this

The Pumper
07-30-2008, 09:56 AM
Pretty nice.

XSiv Force
07-30-2008, 09:58 AM
thank ya uch i need to find some place that has a P-40 Warhawk Shark Smile to place around the front of the barrel

DirtySouth
07-30-2008, 09:58 AM
How's it work?

XSiv Force
07-30-2008, 10:02 AM
well Load nerf rocket in to barrel..............screw the a 12 gram into the quick change while the ball valve is in the off position **VERY IMPORTANT** Then point at target and shoot it will shoot a pocket vortex about 250 ft

DirtySouth
07-30-2008, 10:05 AM
Coolio...Sounds dangerous. :D

XSiv Force
07-30-2008, 10:07 AM
Parts needed:
12 gram quick change
2" Diameter X 15" long PVC
2" PVC End Cap
90 degree Steel Elbow
1" long Galvanized Steel Pipe
5" Long Galvanized Steel Pipe
Steel Pipe Ball Valve
Steel Pipe Reducer to fit quick change to rest


All Steel pipe need s to be 3/4"

Ace24
07-30-2008, 10:11 AM
How heavy is it?

XSiv Force
07-30-2008, 10:14 AM
Instructions:
1) Drill Hole in PVC to fit the elbow into PVC start witha .5" bit and file out to fit
2) Place end cap onto end of PVC and slam cap onto by poping it on ground a few times
3) Using a table top vice clamp screw parts on in this sequence
Elbow-1" pipe-ball valve-5" pipe-reducer-quick change

I suggest using plumbers tape(teflon) on the screw parts to seal leaks.
**Note** The 5" pipe is basically the expansion chamber dont go any smaller than 5". The 12 grams have 500 psi the ball valve is rated around 600 psi

4) Screw the assembly onto the PVC use a sealant as extra protection the stop any other seal around the joints

XSiv Force
07-30-2008, 10:15 AM
How heavy is it?

About the 3 lbs i think with every in it ready to fire :D

TheDarkShadow
07-30-2008, 10:22 AM
Vid Vid Vid Vid

XSiv Force
07-30-2008, 10:24 AM
if i can get a digi camerea i would

Actually i would love to see if it is possible to shoot of a tippmann Big bog grenade and it still work

police_brutality
07-30-2008, 11:00 AM
http://www.houndsofhellpaintball.com/articles1.html

instructions and vids

XSiv Force
07-30-2008, 11:02 AM
yep, but dont haet up the pipes

xsvly-fat
07-30-2008, 12:14 PM
That looks really cool but heavy lol

EDIT: I'm suprised it doesn't weigh more

XSiv Force
07-30-2008, 01:13 PM
ways alot less than any of my piranhas fully loaded

irishwarrior
07-30-2008, 01:15 PM
Well, your design's a lot lighter than mine :p. I'm going to be using a full-size CO2 tank.

XSiv Force
07-30-2008, 01:19 PM
only need one shot tho :dodgy:

irishwarrior
07-30-2008, 01:20 PM
Not on a speedball course :D

XSiv Force
07-30-2008, 01:21 PM
need a clip feed then

irishwarrior
07-30-2008, 01:22 PM
You're right! I need to satisfy my need for modding anyway. Great Idea!

XSiv Force
07-30-2008, 01:28 PM
either like a WWII Anit -Air or revolver style would be cool

DFSniper
07-30-2008, 03:36 PM
hey, if you look up the site for that grenade launcher shady has on his gun, they have stuff (cardboard) that fits in the tube and you load it with about 50 paintballs (or a grenade). the cardboard acts pretty much like a bullet casing except that it stays with the projectile until it leaves the barrel. you should do something like that for a shotgun effect :D

irishwarrior
07-30-2008, 04:04 PM
^That's called a sabot. It's generally used regardless of ammo.

DFSniper
07-30-2008, 04:08 PM
yeah, thats the word... it slipped my mind. thats pretty bad considering my dad's a tanker...

XSiv Force
07-30-2008, 06:35 PM
well actually i was going to try to make one a lil smaller that would fit onto the front of one of my guns and either shhot the rocket or the sabot

XSiv Force
07-31-2008, 02:21 PM
i am in need of some ideas for making a breach loading canon any chance any of you guys have pic that i can scale down

DFSniper
07-31-2008, 02:33 PM
cannon as in 2-wheeled artillery cannon??

mount the 12g on top (where the fuse would go) and attach a pull string to the valve handle :p

GL finding working wagon wheels though...

irishwarrior
07-31-2008, 04:47 PM
Tractor Wheels FTW!!!!

XSiv Force
07-31-2008, 06:23 PM
ok wrong word grenade launcher under barrel style

Modded-Like-Hell
07-31-2008, 06:38 PM
if you put a handfull of paintballs in it will it launch them out far? lol

XSiv Force
07-31-2008, 06:45 PM
i dont think it would have a problem but i would like to make a sabot round tho so no paintballs end up clogging the pipe

irishwarrior
07-31-2008, 06:46 PM
You could do a "Street Sweeper"-type setup here (http://www.lakesideguns.com/c3gallery/sweepers.html)

XSiv Force
07-31-2008, 06:47 PM
what cha mean?

irishwarrior
07-31-2008, 06:48 PM
Like a scaled down breach-break revolving chamber grenade launcher.

XSiv Force
07-31-2008, 06:50 PM
ah..............not willing to spend that much time or money on it :dodgy: :D

irishwarrior
07-31-2008, 06:52 PM
Then I will! :D