View Full Version : J&J Full Tilt Ceramic

01-31-2006, 04:42 PM
Has anyone tried a J&J Full Tilt Ceramic in the MR2? Will it fit?

01-31-2006, 05:58 PM
Well, seeing as the MR2 is like anyother spyder, when it comes to barrel threads, any spyder threaded barrel will fit, including the J&J Performance Full Tilt Ceramic barrel. If you buy one, then make sure to select Spyder Threads.

01-31-2006, 07:35 PM
Actually, the front "MR2 Shroud" fits TIGHTLY AROUND the barrel. Barrels that are too large in their outer diameter will not fit.

02-01-2006, 12:17 PM
I have the JandJ on my MR1, it should fit on the MR2

02-01-2006, 03:30 PM
The MR1 DOES NOT have a shroud, the MR2 DOES. Any Spyder barrel will fit a MR1 while only low profile barrels will fit the MR2.

QRFleader, How is your Full Tilt working out for you?

02-02-2006, 02:18 PM
I love it, may accuracy doubled with the change over the stock. I have the same range as my buddies Angel. Most of the people I play with Run A5's or 98's all running the flatline and I can stay close in range with mine.

The new spring kit may have a little to do with it.

02-05-2006, 03:51 PM
The MR1 doesnt have that deep plastic ribbed recess that the barrel slides into before it contacts the threads???

02-05-2006, 03:54 PM
Heh....no kidding! He's right...I just compared the two pictures. It doesnt have the same front end setup

02-05-2006, 08:51 PM
I am seeing on ebay (http://cgi.ebay.com/J-J-EDGE-ELITE-KIT-FOR-ION-SPYDER-TIPPMANN-98-and-A-5_W0QQitemZ7216796986QQcategoryZ16046QQssPageNameZ WDVWQQrdZ1QQcmdZViewItem) a J&J Edge Elite Kit (5 backs and 3 fronts) for less than $90...

Looks like I found my new toy :)

02-05-2006, 10:11 PM
my Jand J is about the same outer diam. as the stock barrel

02-23-2006, 10:54 AM
is this one will fit on the spyder mr2 ?

http://cgi.ebay.com/Black-14-J-J-Spyder-Ceramic-Sniper-Paintball-Barrel_W0QQitemZ7220159840QQcategoryZ47233QQrdZ1QQ cmdZViewItem

02-23-2006, 10:56 AM
http://cgi.ebay.com/Black-14-J-J-Spyder-Ceramic-Sniper-Paintball-Barrel_W0QQitemZ7220159840QQcategoryZ47233QQrdZ1QQ cmdZViewItem

03-24-2006, 02:10 PM
It fits.....


03-26-2006, 10:42 AM
nice :D

03-29-2006, 07:37 PM
Which length would you recommend...16" or 20"??

03-29-2006, 09:10 PM

08-19-2006, 06:50 PM
i just got a mr2 and a j&j full tilt barrel, it WILL NOT FIT with the mr2 shroud, you just have to take it off which isnt too complicated, like 2-3 posts on how to do it in the forums

08-23-2006, 06:42 PM
Ummmm sk1m4sta, it does fit. I own one as well and it fits perfectly, also the photographic evidace in the post above would also support this. :)


Correction, sorry must have gotten my wires crossed between the ceriamic barrels above and the multi piece barrel set... The barrel kit backs will not fit, the singel piece ones will. Sorry for the confusion :)