PDA

View Full Version : getting a vs more lp


samus129
04-21-2007, 02:22 PM
is there any way to get the vs to work on less psi then gust polishing sear and inside of the gun.

CareBear-Killer
04-26-2007, 09:46 PM
You could try the newer bolt and striker from alamocitypb.com

Not sure how much less air it would use, but the new, lighter striker should help to lower the psi a little.

Opteron-O3
04-28-2007, 04:37 AM
worry about efficiency. everything else is pretty good.

spitfirocks
04-28-2007, 09:35 AM
opteron-03, how can you make it more efficient
?

Opteron-O3
04-28-2007, 10:13 AM
Adjusting the springs. Mainly the valve spring

Prem205 and I have been experimenting and have come to the conclusion that the Medium Spring from the 32* Degrees Kit has the best results.

Prem205 has gotten around 800shots from a 47/3000. If that doesn't impress you, I don't know what will.
I was able to get around the same amount with a stock setup.

It's worked for both of our guns, so I assume it'll work for all other VS Markers, but remember, Kingman's tolerances aren't the same for every gun.

spitfirocks
04-28-2007, 12:03 PM
how would u make it more efficient with stock springs?

Opteron-O3
04-28-2007, 01:27 PM
You can't.

samus129
04-28-2007, 01:29 PM
thax every one so far i still keep options open.

spitfirocks
04-28-2007, 02:40 PM
Adjusting the springs. Mainly the valve spring

Prem205 and I have been experimenting and have come to the conclusion that the Medium Spring from the 32* Degrees Kit has the best results.

Prem205 has gotten around 800shots from a 47/3000. If that doesn't impress you, I don't know what will.
I was able to get around the same amount with a stock setup.

It's worked for both of our guns, so I assume it'll work for all other VS Markers, but remember, Kingman's tolerances aren't the same for every gun.


than what that?

Opteron-O3
04-28-2007, 03:28 PM
Stock setup as in bottom-line regulator and foregrip. While using the medium valve spring. Compared to my friends Upgraded V/A, CP Regulator, ON/OFF and medium valve spring.

I was hoping you would understand without having to repeat myself... guess not.

MVS1
04-28-2007, 03:56 PM
A bolt w/orings, a barrel kit so you can match paint to bore size and a few other things come to mind that would make a difference when it comes to efficiency. The VS is already operating at a very respectable low pressure...springs, lightened strikers and such can bring that number down but as opteron stated efficiency is what really makes the difference.

Hob Hayward
04-28-2007, 05:04 PM
Running on Co2 would possibly help get a lower pressure... If you had a stab.

Would need a higher dwell, but you would be able to go lower without sputtering issues.

STRIKEFIRST
04-29-2007, 07:07 AM
Opte - medium valve huh...what is the stock like a 32 degrees hard?

Opteron-O3
04-29-2007, 07:09 AM
The stock valve spring is light. Equivalent to the black spring in the 32* set.

STRIKEFIRST
04-29-2007, 07:17 AM
whats your psi at then?

Opteron-O3
04-29-2007, 07:29 AM
Should be around the same. More or less.

As I said earlier. Every spyder isn't the same so maybe the results will vary.

Prem205 was able to get 190psi @ 290fps. I was able to do 220psi @ 290fps

samus129
04-29-2007, 08:36 AM
thax for the help i guna try getting a 32* kit and try it in mine.
edit:
mvs1 - to get a lower operating pressure because a barrel kit is expensive.

Opteron-O3
04-29-2007, 08:40 AM
Awesome!