View Full Version : help, expansion chamber

04-09-2007, 10:06 AM
i just got a deal on an expansion chamber for my gun aggressor xt, and i want to add it to my gun. what is the easiest way to add the expansion chamber without going to a remote system?

04-09-2007, 10:11 AM
Add a vertical adapter [VA] I think.

04-09-2007, 10:18 AM
i,ve thought about that but its not easy my air line goes straight body of the gun.

04-09-2007, 01:37 PM
what gun do you have?? Post a pic if you can!

04-09-2007, 01:38 PM
for my gun aggressor xt:cool:

04-09-2007, 05:34 PM
lol, thats what happens when im at work and trying to be sneaky......

you need this

http://cgi.ebay.com/32-Degrees-Stainless-Steel-Spyder-Vertical-Adapter-NEW_W0QQitemZ130098778884QQihZ003QQcategoryZ47239Q QrdZ1QQcmdZViewItem

your expansion chamber will thread into that adapter ;)

04-10-2007, 11:18 PM
i seeing it and trying, do you need to remove the threads from the gun and screw that in?

04-11-2007, 01:33 AM
Hmm... This'll be tricky... That one that you linked will not work. The threads on the body are male, and that one's for female. Reference Diagram. (http://www.ultratwistedpaintball.biz/mm5/parts/kingmanspyderaggressorxtparts.pdf)

It'll be tricky to put an expansion chamber on your marker, but I'll do some research and see what I can come up with as for a solution. ;)

04-12-2007, 09:16 AM
ive seen it done, with my gun. thats why im asking i need an adapter with female threads.

i have a picture on the same model gun as mine with the setup i want on it, if i can post a pic i would.

i put the pic of the same gun with xpansion chamber as my avatar for now.

04-12-2007, 11:31 AM
not having it infront of me is hard, but even from that diagram, that male thread should unscrew from the body, I dont think they make a gun with threads molded into the frame. Try to unscrew it, it looks like how my old spyder classic was set-up. Then screw in that adapter I linked for you.


use that adapter in the link and find a female/female connector in the plumbing section at a hardware store.

but try to unscrew it, I would find if rather odd that that piece is stuck in the frame permantly. :)

04-13-2007, 10:09 AM
well i got the threads of the gun now, hopefully the threads on the verticle adapter r the same as the one on the gun..lol

the piece i took of the gun has two different threads the ones into the gun are a fine thread and the hose side is courser. well ill find out when the adapter gets here. lets hope it all works out.

one other thing, my gun worked good last time i used it ten it acted like it was out of air, it would not recock(it spuutered) after it shoot would lack of oil/bad o-ring cause this? i can get one to two shots out of the gun after it has sat for a while with no problem then it does the same thing.

04-14-2007, 02:49 PM
do you have a full tank of air?? Check the cup seal and all o rings and let us know if they are all ok!

04-15-2007, 09:01 PM
i oiled the gun today and the oring look fine and ill try shooting it again in the morning, the tank was working fine with the spare gun m friend had its getting low but it acted with a fresh fill up, and worked great on the brass eagle back up.

im going to try it with oiled orings now that i got some oil and the cup seal seems fine last i looked, it probably will be the problem since i had a spare but i lost it yesterday...lol:D

05-02-2007, 09:35 AM
got everything setup now i ut need some 2 to try it