PDA

View Full Version : spyder mr1 problems.


NoRcO_bOi
04-07-2007, 11:32 AM
Hey, I am having a problem with my Spyder mr1. It won't cock. I put all the parts in pull back on the thing that is attacked to the hammer and it won't catch the spring just springs it back forward. Do you guys know the problem?

Hob Hayward
04-07-2007, 11:46 AM
Is your grip frame attached to the gun? If it is, make sure its on tight.

NoRcO_bOi
04-07-2007, 11:47 AM
How do I make sure it is tight?

NoRcO_bOi
04-07-2007, 02:01 PM
it isn't even cocking when I don't put my co2 tank into it:S

Kenny_McCormic
04-07-2007, 02:05 PM
something is wrong with your trigger frame

NoRcO_bOi
04-07-2007, 03:02 PM
alright, can you tell me what? and how to fix it please?

Taillo
04-07-2007, 04:56 PM
If your problems began after disassembling the bolt, you may have reassembled it wrongly. I had this problem once and i was not able to fix it till i reassembled it right. One way to see if it is wrongly assembled, push down the cocking knob, if it goes way lower than usual, its not correct. Try to disassemble the bolt and reassemble it, you may find what is wrong.

kidonfire
04-07-2007, 04:57 PM
tighten the screws on your trigger fame first. If that doesn't work then check the sear to make sure it isn't rounded.

alam3503
04-07-2007, 07:23 PM
hammer upside down??? I dont think that is possible. but the sear sounds like the problem

Ace24
04-07-2007, 08:49 PM
If your problems began after disassembling the bolt, you may have reassembled it wrongly. I had this problem once and i was not able to fix it till i reassembled it right. One way to see if it is wrongly assembled, push down the cocking knob, if it goes way lower than usual, its not correct. Try to disassemble the bolt and reassemble it, you may find what is wrong.

Not true. Mine is assembled right and I can still push the cocking pin all the way down to the frame.

Your hammer is upside down. That or your trigger frame isnt attatched right. It also could be that your bolt itself is upsidedown. Make sure the slot for the detent is facing the feedneck side of the gun when putting it back in.

Hob Hayward
04-08-2007, 07:59 AM
If you're sure its not the frame, take out all the internals, and put them back the way the diagram that came with the gun shows.

NoRcO_bOi
04-08-2007, 10:18 AM
the problem is my mom threw away the diagram so I'm not sure how they go in. So how do i fix the trigger frame and fix the internals, also what is the detent and how do i know it is facing the feedneck?

Hob Hayward
04-08-2007, 10:44 AM
http://www.spyder.tv/section/support/diagrams/mr1.pdf

NoRcO_bOi
04-08-2007, 11:57 AM
um, when i downloaded the file it was in all gibberish... like this.


%PDF-1.4
%

4 0 obj
<<
/Linearized 1
/O 6
/H [ 2536 316 ]
/L 851038
/E 835785
/N 1
/T 850841
>>
endobj
xref

NoRcO_bOi
04-08-2007, 01:11 PM
alright, I am pretty sure that the internals are in right. But it still won't catch....


EDIT: made a video off my webcam, putting it on youtube now.

Taillo
04-08-2007, 04:07 PM
Not true. Mine is assembled right and I can still push the cocking pin all the way down to the frame.



All the way down? If you push it down, the larger part of the cocking pin is not supposed to touch the frame, if it does, there is something wrong, or you dont have the same bolt as me.

NoRcO_bOi
04-08-2007, 06:24 PM
alright I have the video on youtube, here is a link. I'm not sure if this is the right link. I fast forwarded it to make it a bit shorter.

http://www.youtube.com/paul4531

NoRcO_bOi
04-08-2007, 09:21 PM
Alright, the screws where really tight to begin with on the trigger frame. If you look in the diagram the screws i tightened where #16 right behind the Fore grip and #16 right by the striker plug. Are these the correct screws? If not which screws should I tighten? BTW: the screws where already tightened.

NoRcO_bOi
04-08-2007, 10:05 PM
Alright it's fixed now, thank you guys for all your help.